background image

English

19

Wiring Method
(3)

Remove the control box lid (Refer to ‘‘5. INDOOR UNIT INSTALLATION’’.)

(4) Add wiring between the remote controller 2 (slave) and the terminal (P1, P2) of the terminal block 

(X1M) for the remote controller in the control box. (There is no polarity.) 

 

(Refer to Fig. 28 and Table 

4) 

NOTE

1.

All transmission wiring except for the remote controller wires is polarized and must match the terminal 
symbol.

2.

In cases of group control, perform the remote controller wiring to the master unit when connecting to the 
simultaneous operation system. (Wiring to the slave unit is unnecessary.)

3.

In case of group control and simultaneous operation system remote controller, choose the remote con-
troller that suits the indoor unit which has the most functions (as attached swing flap).

4.

For simultaneous operation system, connect the remote controller cord to the master unit.

10. FIELD SETTING

Complete all the “1. Items to be checked after completion of work” on page 4.

Make sure that the installation and wiring work for the indoor and outdoor units is all completed.

Make sure that the following items are all closed: the control box lid of the indoor unit and the outer board 
and piping cover of the outdoor unit.
<Field setting must be made from the remote controller in accordance with the installation conditions.>

Setting can be made by changing the “Mode No.”, “FIRST CODE NO.”, and “SECOND CODE NO.”.

For setting procedures and instructions, see the manual provided with the remote controller.

NOTE

The “Mode No.” is normally set collectively for a group. In order to set each indoor unit individually and per-
form checks after the settings, specify the Mode No. in parenthesis.

Do not perform settings that are not listed in the table.

Upper case of
remote controller

Lower case of
remote controller

Insert the screwdriver 
here and gently work 
off the upper part of 
remote controller.

Fig. 29

S

M

S

S

M

Remote 
controller printed 
circuit board

  

(Factory setting)

(Only one remote 
controller needs 
to be changed if 
factory settings 
have remained 
untouched.)

Fig. 30

3P184443-9J_FM6.book  Page 19  Wednesday, December 14, 2011  10:29 AM

Содержание FAQ71CVEB































Отзывы: