background image

18

English

 When implementing group control

When using as a pair unit or as a master unit for simultaneous multiple unit operation, you may carry out 
simultaneous start/stop (group) control up to 16 units with the remote controller. 

(Refer to Fig. 27 )

In this case, all the indoor units in the group will operate in accordance with the group control remote controller.

The body thermo is effective only for the indoor unit to which the remote controller is connected.

Wiring Method
(1)

Remove the control box lid. (Refer to ‘‘5. INDOOR UNIT INSTALLATION’’.)

(2)

Lay crossover between the terminals (P1, P2) inside the control box for the remote controller. (There is no 
polarity.) 

(Refer to Fig. 26 and Table 4)

NOTE

Terminal numbers of outdoor and indoor units must agree.

Two remote controllers control (Controlling 1 indoor unit by 2 remote controllers)

When using 2 remote controllers, one must be set to “MAIN” and the other to “SUB”.

MAIN/SUB CHANGEOVER

If BRC1E model remote controller is used, see the manual attached to the remote controller.
If the remote controller is a wired one, change the switch setting as follows:

(1)

Insert a flat screwdriver into the clearance between the upper case and the concave of the lower case and, 
remove the upper case. (2 places) (Printed circuit board is attached to the upper part of the remote con-
troller.)  

(Refer to Fig. 29)

(2)

Turn the 

main/sub changeover

 switch on one of the two remote controller printed circuit boards to “S”. 

(Leave the switch of the other remote controller set to “M”.)  

(Refer to Fig. 30)

Outdoor unit 1

Outdoor unit 2

Outdoor unit 16

Indoor unit 1

Indoor unit 
(slave)

Indoor unit 2 
(Master)

Group control remote controller

Indoor unit 16

Fig. 27

P

1

P

2

P

1

P

2

P

1

P

2

1 2 3

1 2 3

NOTE)

Main power supply

Outdoor unit

Indoor unit

Remote 
controller
(Optional 
accessories)

Remote 
controller
(Optional 
accessories)

2 remote controllers control

Earth leakage 
circuit breaker

Fig. 28

Outdoor unit

Indoor unit
(slave)

Indoor unit 
(Master)

Remote 

controller 2

Remote 

controller 1

3P184443-9J_FM6.book  Page 18  Wednesday, December 14, 2011  10:29 AM

Содержание FAQ71CVEB































Отзывы: