background image

            

D-EIMHP01601-22_01EN 16/26     
 

pressures and temperatures of the system, it must also be resistant to the used glycol in the water. 

The external surface of the water pipes must be adequately protected against corrosion.

 

10.2 

Water charge, flow and quality 

To assure proper operation of the unit a minimum water volume is required in the system and the water flow through the 
evaporator must be within the operation range as specified in the table below.  

Table 6-Water flow operation range 

 

Minimum 

water volume (l) 

Minimum 

water flow 

Maximum 

water flow 

EWWQ014 

62 

31 l/min     75 l/min 

EWWQ025 

134 

53 l/min 

123 l/min 

EWWQ033 

155 

76 l/min     186 l/min 

EWWQ049 

205 

101 l/min 

247 l/min 

EWWQ064 

311 

152 l/min 

373 l/min 

10.3 

 Water piping insulation 

 

The complete water circuit, inclusive all piping, must be insulated to prevent condensation and  reduction of the cooling 
capacity. 

10.4 

 Refrigerant piping insulation 

 
To prevent burning injuries by accidental touching the hot (max 

135°C

) discharge pipe, it must be insulated thoroughly. 

A minimum of insulation to protect the liquid pipe from damage is advisable. 

10.5 

Antifreeze protection for BPHE and recovery exchangers 

 

If the exchangers are completely empty and cleaned with antifreeze solution, additional methods can be used against 
freezing. 
The following protection methods must be considered when designing the system as a whole: 
 

1.  continuous water flow circulation inside piping and exchangers. 

 

2.  addition of an appropriate amount of glycol inside the water circuit or, as alternative, an additional heat 

insulation and heating of exposed piping (internal and external to the unit).  

 

3.  if the unit does not work during the winter season, emptying and cleaning of the heat exchanger.  

It is the responsibility of the installer and/or of local maintenance personnel to ensure that described antifreeze meth ods 
are used. 
Make sure that appropriate antifreeze protection is always maintained. Failing to follow the instructions above could 
result in unit damage. 

 

 

Damage caused by freezing is excluded from the warranty, therefore Daikin Applied Europe S.p.A. 
declines all responsibility.

 

 

 

 

 

 

 

 

 

 

 

 

Содержание EWLQ025KCW1N



























Отзывы: