Daikin DRG0361DL00001S Скачать руководство пользователя страница 5

Страница: 5 / 113

PRODUCT IDENTIFICATION

NOMENCLATURE

•

Stainless-Steel Heat Exchanger (Gas only units): A

tubular heat exchanger made of 409-type stainless steel

is installed in the unit.

•

Economizers (Downflow): Based on air conditions, can

provide outisde air to cool the space.

•

Electric Heat Kits (heat pump and cooling units only):

Available in all voltage options.

•

Non-powered Concenience Outlet: A 120V, 15A, GFCI

outlet makes it easier for technicians to service the unit

once an electrician runs power to the outlet.

•

Powered Concenience Outlet: A 120V, 15A, GFCI outlet

powered with a transformer built into the unit. When

a factory-installed powered convenience outlet is

installed in the equipment, the unit MCA (Min. Circuit

Ampacity) will increase by 7.5A for 208/230V units,

increase by 3.75A for 460V units, and by 3A for 575V

units. The MOP (Max. Overcurrent Protection) device

must be sized accordingly.

•

Disconnect Switch (non-fused; 3-phase units only:)

A disconnect switch is installed in the unit and

factory wiring will be complete from the switch to

the unit. Please note that for air conditioning and

heat pump models, the appropriate electric heat

kit must be ordered to be factory-installed along

with the disconnect switch (non-fused) when it is

ordered. Please note that for models with a powered

convenience outlet option and a disconnect switch

(non-fused) option, the power to the powered

concenience outlet will be shut off when the disconnect

switch (non-fused) is in the off position.

•

Return Air and/or Supply Air Smoke Detectors: Return

air and/or supply air smoke detectors are installed in

the unit.

•

Hinged Access Panels: Allows access to unit's major

components. Combined with latches for easy access

to control box, compressor, filters and blower motor.

Available on all units.

•

Two-speed indoor fan blower models are available on

6, 71/2, 81/2, 10, 121/2, 15, 20 & 25 ton units. Section

6.4.3.10.b of ASHRAE Standard 910.1-2010 and Section

6.5.3.2.1.a of ASHRAE Standard 90.1-2013 require a

minimum of two fan speeds. Section 140.4(m)1 of

California Energy Commission Title 24 2013 cibtaubs a

similar provision. When the units with the two-speed

infoor fan blowers operate on a call for the first stage

of cooling, the fan operates at low speed, which is 66%

of full speed. When the units operate on a call for the

second stage of cooling, the fan operates at full speed.

In heating operation, the fan operates at full speed.

During ventilation operation, the fan operates at low

speed.

•

Return Air and/or Supply Air Smoke Detectors: Return

air and/or supply air smoke detectors are installed in

the unit.

•

Hinged Access Panels: Allows access to unit's major

components. Combined with latches for easy access

to contol box, compressor, filters and blower motor.

Available on all models.

•

Phase Monitor: Phase monitor (3 phase only), available

for 3-25 ton DB and DR series models. Phase monitor

shall provide protection for motors and compressors

against problems caise by phase loss, phase reversal

and phase unbalance. Phase monitor is equipped with

an LED that provides an ON or FAULT indicator.

Содержание DRG0361DL00001S


















































































































Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды

Daikin DRG0361DL00001S, Инструкция по эксплуатации

Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды