Daikin DRG0361DL00001S Скачать руководство пользователя страница 26

Страница: 26 / 113

SYSTEM OPERATION

CLEARANCES

24" MIN.

36” MIN.

Unit Clearances

*In situations that have multiple units, a 36” minimum

clearance is required between the condenser coils.

Adequate clearance around the unit should be kept for

safety, service, maintenance, and proper unit operation.

A clearance of 48” is recommended on all sides of

the unit to facilitate possible parts replacement, to

allow service access and to insure proper ventilation

and condenser airflow. The top of the unit should be

completely unobstructed. If units are to be located under

an overhang, there should be a minimum of 48” clearance

and provisions made to deflect the warm discharge air out

from the overhang. The unit should be installed remote

from all building exhausts to inhibit ingestion of exhaust air

into the unit fresh air intake.

NOTE: If the 36” minimum clearance is used on the

control panel side of a DRG unit, a flue extension kit

needs be to installed to prevent flue gas recirculation. See

table below for the kit selection.

Model size

Kit part number

3 ton

HEFLUE036

4 & 5 ton

HEFLUE048060

6 ton

HEFLUE072

Flue Extension Kits

Roof Curb Installation

ROOF CURB POST-INSTALLATION CHECKS

After installation, check the top of the curb, duct

connection frame and duct flanges to make sure gasket has

been applied properly. Gasket should be firmly applied

to the top of the curb perimeter, duct flanges and any

exposed duct connection frame. If gasket is loose, re-apply

using strong weather resistant adhesive.

Protrusion

Inspect curb to ensure that none of the utility services

(electric) routed through the curb protrude above the

curb.

CAUTION

If protrusions exist, do not attempt to set unit on

curb.

ROOF TOP DUCT CONNECTIONS

Install all duct connections on the unit before placing the

unit on rooftop.

Horizontal Discharge

Refer to IOD-7082 included in the literature pack for

installing horizontal duct covers.

Flexible duct connectors between the unit and ducts are

recommended. Insulate and weatherproof all external

ductwork and joints as required and in accordance with

local codes.

Содержание DRG0361DL00001S


















































































































Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды

Daikin DRG0361DL00001S, Инструкция по эксплуатации

Результаты поиска

Содержание DRG0361DL00001S

Отзывы:

Похожие инструкции для DRG0361DL00001S

Бренды по названию

Популярные бренды