background image

English

English

12

Trial Operation and Testing

1. 

Trial operation and testing

1-1  Measure the supply voltage and make sure that it falls in the specified range.
1-2  Trial operation should be carried out in either cooling or heating mode.

• In cooling mode, select the lowest programmable temperature; in heating mode, select the highest programmable 

temperature.
1) Trial operation may be disabled in either mode depending on the room temperature.

Use the remote controller for trial operation as described below.

2) After trial operation is complete, set the temperature to a normal level (26°C to 28°C in cooling mode, 20°C to 24°C in 

heating mode).

3) For protection, the system disables restart operation for 3 minutes after it is turned off.

1-3  Carry out the test operation in accordance with the operation manual to ensure that all functions and parts, 

such as louver movement, are working properly.

• The air conditioner requires a small amount of power in its standby mode. If the system is not to be used for some 

time after installation, shut off the circuit breaker to eliminate unnecessary power consumption.

• If the circuit breaker trips to shut off the power to the air conditioner, the system will restore the original operation 

mode when the circuit breaker is opened again.

Trial operation from remote controller

1)  Press “ON/OFF” button to turn on the system.
2)  Press “TEMP” button (2 locations) and “MODE” button at the same time.
3)  Press “TEMP” button and select “

T

”.

4)  Press “MODE” button.
5)  Trial operation terminates in approx. 30 minutes and switches into normal mode. To quit a trial operation, press  

“ON/OFF” button.

2. 

Test items

Test items

Symptom

(diagnostic display on RC)

Check

Indoor and outdoor units are installed properly on solid bases.

Fall, vibration, noise

No refrigerant gas leaks.

Incomplete cooling/heating 
function

Refrigerant gas and liquid pipes and indoor drain hose extension are 
thermally insulated.

Water leakage

Draining line is properly installed.

Water leakage

System is properly earthed.

Electrical leakage

The specified wires are used for inter-unit wiring.

Inoperative or burn damage

Indoor or outdoor unit’s air inlet or air outlet has clear path of air.
Stop valves are opened.

Incomplete cooling/heating 
function

Indoor unit properly receives remote control commands.

Inoperative

 will appear when the MODE button is pressed.*

No heating

* If the      is not displayed, change the dipswitch setting 

for the remote controller.
Slide the dipswitch to the left-hand side.
Press the MODE button again and check that      
appears on the LCD of the remote controller.

Dipswitch

01_EN_3P297034-1.indd   12

10/12/2011   11:37:08 AM

Содержание CTXS15K2V1B


















Отзывы: