Daikin BRC7EA628 Скачать руководство пользователя страница 11

English

9

NOTE

Stop flaps from swinging before trying to 
angle them. Working while the flaps are 
moving may get your fingers pinched.

MOVEMENT OF THE AIR FLOW FLAP

For the following conditions, micro computer 
controls the air flow direction so it may be 
different from the display.

NOTE

If you try cooling or programmed drying 
while the flaps are facing downward, air 
flow direction may change unexpectedly. 
There is nothing wrong with the equipment. 
This serves to prevent dew formed on parts 
in the air discharge outlet from dripping.

Operation mode includes automatic 
operation.

Operate in the following order.

The timer is operated in the following two 
ways.
Programming the stop time (

.... The system stops operating after the 
set time has elapsed.
Programming the start time (

.... The system starts operating after the 
set time has elapsed. 

The timer can be programmed a maximum 
of 72 hours.

The start and the stop time can be simulta-
neously programmed.

Operation 
mode

Cooling

Heating

Operation 
conditions

When operating 
continuously at 
downward air 
flow direction

When room 
temperature is 
higher than the 
set temperature

At defrost 
operation
(The flaps blow 
horizontally to 
avoid blowing 
cold air directly 
on the occupants 
of the room.)

PROGRAM TIMER OPERATION

Press the TIMER MODE START/STOP 

button several times and select the 

mode on the display.

The display flashes.
For setting the timer stop .... “

For setting the timer start .... “

Press the PROGRAMMING TIME but-

ton and set the time for stopping or 

starting the system.

When this button is pressed, the 

time setting advances by 1 hour.

When this button is pressed, the 

time setting goes backward by 1 

hour.

Press the TIMER RESERVE button.

The timer setting procedure ends. 
The display changes from flashing light to a 
constant light.

Press the TIMER OFF button to cancel

 

programming. The display vanishes.

TIMER MODE 
START/STOP

PROGRAMMING TIME

TIMER RESERVE

TIMER CANCEL

TIMER

DOWN

UP

DOWN

UP

RESERVE

CANCEL

3PEN505118-2B.book  Page 9  Thursday, January 7, 2021  10:28 AM

Содержание BRC7EA628





















Отзывы: