Daikin (A)5LLF Скачать руководство пользователя страница 47

Страница: 47 / 51

Si50-203

Index

Airtightness Test ....................................................29
Assembling The Screw Shaft and Main Bearing

Holder .............................................................24

Caution in Test Operation ......................................31
Changing Refrigerating Oil

Changing Procedure ..........................................6

Charging Oil ...........................................................30
Charging oil ..............................................................7
Cleaning The Suction Filter ......................................9

Disassembling The Gate Rotor and Surrounding

Parts ................................................................12

Disassembly and Inspection  ..................................11
Disassembly of The Controller  ...............................16
Draining Oil  ............................................................11

Final Assembly .......................................................24

Inserting The Screw Shaft ......................................25
Inspecting The Gate Rotor .......................................7
Inspection of The Gate Rotor and Surrounding

Parts ................................................................12

Installation of Bearings

Installing and Adjusting The Gate Rotor

Bearings ..............................................23

Main Shaft Bearing ..........................................22

Installing The Discharge End Cover

(In case of ZH9F, Oil collector) .......................28

Installing The Gate Rotor and Adjusting

The Slit Clearance ..........................................27

Installing The Main Bearing Holder Fixing Plate,

Assembling The Controller, and Installing
The Oil Filter ...................................................28

Installing The Motor Rotor ......................................25
Installing The Suction End Cover ...........................26
Insulation Resistance of The Motor ..........................5
Insulation Resistance Testing

Measurement Standard .....................................5
Measuring Procedure ........................................5

Overhaul ...................................................................3
Overhaul Instructions .............................................10

Periodic Inspection ...................................................4
Periodic Inspection Instructions ...............................5
Periodic Inspection Items and Intervals ...................4
Positioning The Screw Rotor ..................................26

Remove The Side Caps (One on Each Side)

and The Discharge End Cover.
(in case of ZH9F, oil collector) ....................... 11

Removing and Disassembling The Screw

Assembly Pulley ............................................. 18

Removing and Installation of Gate Rotor .............. 14
Removing Bearings

Gate Rotor Bearings (Angular-Contact Bearing,

Deep Groove Ball Bearing) ................ 21

Main Shaft Bearing ......................................... 20

Removing The Motor Rotor ................................... 15
Removing The Suction End Cover ........................ 14
Replacing The Bearing .......................................... 20
Required Tools

List of general tools and measuring

instruments ........................................ 32

List of special tools ......................................... 32

Scope of Application ............................................... 2

Tightening torque values for bolts (N - m) ............. 32

Содержание (A)5LLF




















































Результаты поиска

Содержание (A)5LLF

Отзывы:

Похожие инструкции для (A)5LLF

Бренды по названию

Популярные бренды

Daikin (A)5LLF, Руководство по обслуживанию

Результаты поиска

Содержание (A)5LLF

Отзывы:

Похожие инструкции для (A)5LLF

Бренды по названию

Популярные бренды