Daikin (A)5LLF Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 51

background image

Si50-203

Overhaul Instructions

Semi-Hermetic Single Screw Compressor Version III

17

(2) Remove the oil filter using the special tool, and clean. (ZH3F only)

After cleaning, dry thoroughly.
If the filter is damaged or torn, replace.

Fig. 4-14 Oil filter removing tool

(3) Remove the mounting bolts, and remove the cylinder cover.
(4) Pull out the piston.
(5) Remove the mounting bolts, and remove the main bearing holder fixing plate.

Use guide bolts when removing the fixing plate, since it is heavy.
Do not lose screw adjusting shims (1) located inside.

(6) Remove the oil filter from the fixing plate, and clean. (except for ZH3F)

After cleaning, dry thoroughly.
If the filter is damaged or torn, replace.

(7) Remove the slide valve from the casing.

Fig. 4-15 Removing main bearing holder fixing plate

«
...
16
17
18
19
20
...
»

Содержание (A)5LLF




















































Отзывы:

Нет отзывов

Похожие инструкции для (A)5LLF

Бренд: York Страницы: 4

Бренд: ZIPPER MASCHINEN Страницы: 45

Бренд: Meec tools Страницы: 36

Бренд: California Air Tools Страницы: 16

Бренд: Hitachi Страницы: 85

Бренд: Jet Страницы: 68

AA-98 AirPac II

Бренд: Aseptico Страницы: 8

LW 230 E II Compact

Бренд: L&W Compressors Страницы: 187

Бренд: Mouvex Страницы: 2

Бренд: California Air Tools Страницы: 15

Бренд: GreenWorks Tools Страницы: 147

Бренд: KAESER Страницы: 348

Бренд: Campbell Hausfeld Страницы: 24

Бренд: Campbell Hausfeld Страницы: 12

Бренд: Wagan Страницы: 1

Black Max 55X12

Бренд: Bushranger Страницы: 12

Бренд: NEKTRA Страницы: 2

Бренд: Xstream Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды