Daikin (A)5LLF Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 51

background image

Overhaul Instructions

Si50-203

14

Semi-Hermetic Single Screw Compressor Version III

(5) Turn the gate rotor shaft to remove it from the screw rotor. Be careful not to damage the

gate rotor.

5. Removing and Installation of Gate Rotor

(1) Remove C type retaining ring.
(2) Remove the gate rotor from the shaft.
(3) Apply red check to the gate rotor, and check that the rotor is free of cracks.

If the rotor is found cracked, replace it with a new one.

(4) Install the gate rotor on the shaft, and mount the C-type retaining ring.

The gate rotor has front and back sides. Position the gate rotor so that the manufacturing
number is visible.

6. Removing The Suction End Cover

(1) Remove all the mounting bolts.
(2) Mount guide bolts in two bolt holes on the upper section.

(Be sure to mount guide bolts, since the suction end cover is heavy.)

(3) In the guide bolt holes, thread the bolts that were removed previously, then remove the

suction cover from the casing.
Locate positioning pins at two locations, and screw them.

Fig. 4-9 Removing suction end cover

«
...
13
14
15
16
17
...
»

Содержание (A)5LLF




















































Отзывы:

Нет отзывов

Похожие инструкции для (A)5LLF

HGX6 R134a series

Бренд: GEA Страницы: 32

Бренд: VERTO Страницы: 56

Бренд: Quincy Compressor Страницы: 87

Бренд: EUROPE PROJECTION Страницы: 20

Бренд: Ingersoll-Rand Страницы: 57

PORTABLE ELECTRIC AIR COMPRESSOR

Бренд: Mi-T-M Страницы: 60

Бренд: Universal Electronics Страницы: 1

Frick QUANTUM LX

Бренд: Johnson Controls Страницы: 140

Fullmotion CF10C

Бренд: Embraco Страницы: 48

Бренд: Emax Страницы: 14

Бренд: Atlas Copco Страницы: 138

Бренд: Campbell Hausfeld Страницы: 24

EX-HG66e Series

Бренд: GEA Bock Страницы: 52

Бренд: Kahlenberg Страницы: 7

Бренд: Sullair Страницы: 80

PRO A49B 200 CT4

Бренд: ABAC Страницы: 100

POWERplus POWX1725

Бренд: VARO Страницы: 10

JEFC050V10B-230

Бренд: Jefferson Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды