Daihen varstroj VARIN 1305E, Руководство по эксплуатации

Страница: 9 / 25

GB
GB
D
8. ERSATZTEILLISTE
Pos.
(Bild.1)
Bezeichnung
VARIN
1305E
VARIN
1605E
VARIN
1805E
VARIN
2005E
gen
VARIN
2005E
CEL
gen
1 Netzkabel 603922 603899 603899 603954 603954
2 Hinterplate PVC 603900 603900 603916 603916 603916
3 Schalter 603901 603901 603901 603901 603901
4 Kabelentlastung 603902 603902 603902 603902 603902
5 Ventilatorhalter 603903 603903 603903 603903
6 Ventilator 603904 603904 603904 603904
7 Boden 603913 603905 603917 603917 603917
8 Frontplate PVC 603906 603906 603918 603918 603918
9
Reduzierstück VP
603919
10 Steckdose komplett VP 603907 603907 603907 603955 603955
11 Knopf 603908 603908 603908 603908 603908
12 Endstufe - Einschub 603914 603910 603920 603956 604620
13 Deckel 603915 603911 603921 603921 603921
14 Trageband 603912 603912 603912 603912 603912
15
Schweiβkabel mit
Elektrodenhalter
699228 681281 681281 681281 681281
16 Masekabel mit Klemme 699229 681282 681282 681282 681282
17 Aufklebel Frontpl. 603924 603923 603925 603926 603926
19
WIG Set
– komplett zum WIG
Schweiβen (opcion)
(600089) (600089) (600089)
Bemerkung: Die Teile unter Bild 1, Pos. 1,10, 11, 14, 15, 16 in 17 sind Verschleissteile.
9. DIENSTLEISTUNGEN UND GARANTIE
Siehe Garantieschein!
IMPORTANT!
This manual been written for expert operators and must be read entirely before operating the
equipment. Persons not conversant with methods and operations of the equipment should
consult the manufacturer.
Do not attempt to set up, operate or service equipment if not qualified to do so or if this manual
has not been read and understood. If in doubt regarding equipment installation and use, consult
the manufacturer (technical assistance department).
1.0. SAFETY REGULATIONS
The welding power source complies with the requirements of IEC60974-1 and IEC60974-10. The use
of welding equipment and welding operations entail hazards for the operator and third persons. The
reading, comprehensions and respect of the safety regulations below are compulsory. Remember that
a sensible operator who is well aware and respectful of his duties is the best guarantee against
accidents. Read and comply with the following regulations prior to connecting, preparing, using or
transporting welding equipment.
1.1. Installation of equipment
Compliance with the following regulations is fundamental to safety:
1. Installation and maintenance of equipment must be performed in compliance with local safety
standards.
2. Pay attention to the state of wear of socket and plug wiring; renew if necessary. Service
the equipment periodically sized wiring.
3. Connect the lead cable as near as possible to the operating area. Earth connections to structural
part of buildings or to other places distant from the operating area will reduce their effectiveness
and increase the danger of electric shock. Do not pass equipment cables through or near lifting
chains, crane cables or any electrical lines.
4. Never use welding equipment near water. Ensure that the surrounding area, including any objects
therein and the equipment, is dry. Repair water leakages immediately. Do not spray water or other
liquids on the machine.
5. Avoid all direct contact with the skin or wet garments with metal parts under tension. Check that
gloves and protection are dry!
6. Always wear gloves and rubber soled shoes when working in wet areas or standing om metal
surfaces.
7. Always turn off equipment when not being used or in the event of power failure. Accidental earth
discharges may cause overheating and fire hazards. Do not leave powered equipment unattended.
1.2. Personal protection and protection of others
Welding operations are a source of radiation, noise, heat and noxious fumes; for this reason,
the protection of the operator and of third persons must be guaranteed with suitable safety
devices and precautions. Failure to observe thee regulations during operation could lead to
serious health risks.
1. Wear fire-resistant work gloves, a heavy duty long-sleeved shirt, trousers without turn-ups and
shoes with high uppers or boots to protect skin from arc rays and metal sparks and a welder's
helmet or cap to protect the hair.
2. Use a protective mask with suitable glass filter (at least NR10) to protect eyes. Take
measures to protect face, ears and neck. Advise other persons in the vicinity to look away and stand
clear of arc rays and hot metal.