Daewoo KOR-1P557S Скачать руководство пользователя страница 8

Страница: 8 / 35

1. KOR-1P5C7S

1. Connect the main lead to an electrical outlet.

2. After placing the food in a suitable container, open the oven door and put it on the plate tray.

3. Close the door securely.

4. The oven door can be opened at any time during operation by touching the door release button on the control

panel.

The oven will automatically shut off. To restart the oven, close the door and then touch START.

5. Each time a pad is touched, a BEEP will sound to acknowledge the touch.

6. The oven automatically cook on full power unless set to a lower power level.

7. The display will show : 0 when the oven is plugged in.

8. When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information

retained.

To erase all information touch, the STOP/CLEAR pad once more. If the oven door is opened during the oven
operation, all information is retained.

9. If the START pad is touched and the oven does not operate, check the area between the door and door is closed

securely. The oven will not start cooking until the door is completely closed or the program has been reset.

Wattage output chart
The power level is set by touching the POWER pad. The chart shows the display, the power level and the percentage
of power.

OPERATIONS AND FUNCTIONS

Make sure the oven is properly installed and plugged into the electrical outlet.

Touch POWER pad.

Power level(Display)

Approximate Percentage of Power

Once

100

100%

Twice

80%

3 times

60%

4 times

40%

Содержание KOR-1P557S




































Результаты поиска

Содержание KOR-1P557S

Отзывы:

Похожие инструкции для KOR-1P557S

Бренды по названию

Популярные бренды

Daewoo KOR-1P557S, Руководство по обслуживанию

Результаты поиска

Содержание KOR-1P557S

Отзывы:

Похожие инструкции для KOR-1P557S

Бренды по названию

Популярные бренды