background image

6

INSTALLATION

1. Steady, flat location.

This microwave oven should be set on a steady, flat surface.
This microwave oven is designed for counter top use only.

2. Leave space behind and side.

All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and,
eventually, cause failure.

3. Away from radio and TV sets

Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna or
feeder and so on. Position the oven as far from them as possible.

4. Away from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.

5. Power supply

•  Check your local power source.

This microwave oven requires a current of approximately 6 amperes, 230 Volts, 50 Hz.
Power supply cord is about 0.6 meters long.

•  The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other

accident causing oven damage. Using low voltage will cause show cooking. We are not responsible for damage
resulting from use of this oven with a voltage of ampere fuse other than those specified.

•  This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same

type. Such a cable can be purchased from DAEWOO and must be installed by Qualified Person. 

6. Examine the oven after unpacking for any damage such as:

A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.

7. Do not operate the oven if it is colder than room temperature.

(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.

EARTHING INSTRUCTIONS

This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric
shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing
wire with a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.

WARNING  :

Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified

electrician or serviceman if the earthing instructions are not completely understood, or if doubt
exists as to whether the appliance is properly earthed, and either:
If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade
earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating
of the extension cord should be equal to or greater than the electrical rating of the appliance, or Do
not use an extension cord.

Содержание KOR-1P557S




































Отзывы: