Daewoo KOR-122M0A Скачать руководство пользователя страница 33

Страница: 33 / 58

Following the procedures below to check if the oven is defective or not.
1. Check grounding before checking trouble.

2. Be careful of the high voltage circuit.

3. Discharge the high voltage capacitor. (see page 26)

4. When checking the continuity of switches or of the high voltage transformer, disconnect one lead wire

from these parts and then check continuity with the AC plug removed. To do otherwise may result in false
reading or damage to your meter.

5. Do not touch any part of the circuity on the touch control circuit since static electric discharge may

damage this control panel.
Always touch yourself to ground while working on this panel to discharge any static charge built up in your
body.

First of all operate the microwave oven following the correct operation described on pages 8~17 by time
cooking, in order to find the exact cause of any trouble.

(TROUBLE 1) The following visual conditions indicate a probable defective touch control circuit or

membrane switch assembly.

TROUBLE SHOOTING GUIDE

1. Incomplete segments.

(A) Segments missing.
(B) Partical segments missing.
(C) Digit flickering other than normal slight

flickering.

(D) ":0" does not display when power is on.

2. A distinct change in the brightness of one or

more numbers in the display.

3. One or more digits in the display are not on

when they should be.

4. Display indicates a number different from one

touched.

5. For example, touch 5 and 3 appears in the

display.

6. Specific numbers (for example 5 and 3) will not

display when the panel is touched.

7. Display does not count down or up with time

cooking or clock operation.

8. Oven is programmable and cooks normally but

no display shows.

9. Display obviously jumps in time while counting

down.

10. Display counts down noticeably too fast while

cooking.

11. Display can not shift from the first stage cooking

to the third stage cooking while 3 phase
cooking (including defrost).

12. Display does not show the time of day when

dear pad is touched (in clock mode).

13. Oven lamp and fan motor and turn table motor

do not stop although cooking is finished.
Check if the RELAY "2" contacts close if they
are close, replace touch control circuit.

LOCK

CUPS

STAGE

DEFROST

WEIGHT TIME

AUTO

START

Содержание KOR-122M0A



























































Результаты поиска

Содержание KOR-122M0A

Отзывы:

Похожие инструкции для KOR-122M0A

Бренды по названию

Популярные бренды

Daewoo KOR-122M0A, Руководство по обслуживанию

Результаты поиска

Содержание KOR-122M0A

Отзывы:

Похожие инструкции для KOR-122M0A

Бренды по названию

Популярные бренды