Daewoo KOR-122M0A Скачать руководство пользователя страница 46

Страница: 46 / 58

3) Display problems

The display trouble shooting data

4) When there is no microwave oscillation.
(1) When touching "START" pad, oven lamp does not turn on.

Fan motor and turnatable motor do not rotate, but cook indicator in display comes on.
* Cause: RELAY "2" does not operate.

DISPLAY NAME

MICOM OUTPUT

TROUBLE

& PIN NO.

IN PIN NO.

STAGE 1, LOCK don't come on.

Digit 1 (G1), 10

STAGE 2, NO don't come on.

Digit 2 (G2), 11

WEIGHT DEFROST, CUPS don't come on.

Digit 3 (G3), 14

TIME DEFROST doesn't come on.

Digit 4 (G4), 12

AUTO START, g don't come on.

Digit 5 (G5), 13

SEGMENT "a" doesn't come on from G1 to G5.

SEGMENT a, 7

SEGMENT "b" doesn't come on from G1 to G5.

SEGMENT b, 6

SEGMENT "c" doesn't come on from G1 to G5.

SEGMENT c, 5

SEGMENT "d" doesn't come on from G1 to G5.

SEGMENT d, 4

SEGMENT "e" doesn't come on from G1 to G5.

SEGMENT e, 3

SEGMENT "f" doesn't come on from G1 to G5.

SEGMENT f, 2

SEGMENT "g" doesn't come on from G1 to G5.

SEGMENT g, 1

LOCK, NO, CUPS, g don't come on.

LOWER BAR h, 9

STAGE1, STAGE2, TIME DEFROST, WEIGHT

UPPER BAR i, 8

DEFROST, AUTO START don't come on.

NO.

CAUSE

MEASUREMENT

RESULT

REMEDY

Defective Display

Refer to "The display

Replace P.C.B.

trouble shooting data"

assembly.

below.

D9
1N4002A

+12V DC

RY2

G5B-12V

40
FAN RY
TRAY RY

IC1

Q11 KRC106M

Display layout
(Top View)

Q12 KRC 106M

Содержание KOR-122M0A



























































Результаты поиска

Содержание KOR-122M0A

Отзывы:

Похожие инструкции для KOR-122M0A

Бренды по названию

Популярные бренды

Daewoo KOR-122M0A, Руководство по обслуживанию

Результаты поиска

Содержание KOR-122M0A

Отзывы:

Похожие инструкции для KOR-122M0A

Бренды по названию

Популярные бренды