background image

7

OPERATION

1. Connect the mains lead to an electrical socket-outlet. 
2. After placing the food in a suitable utensil, open the oven door and put it on the glass turntable, Glass turntable

must always be in place during cooking.
In case the oven is operated in the grill mode, use the Metal Rack and place food on the metal Rack. 

3. Shut the door.

Make sure that it is firmly closed.

4. How to set each function.

To set MICROWAVE Cooking.

• Set the variable POWER SELECTOR to desired power level.

To set GRILL Cooking

• Set the POWER SELECTOR to the 

(gril) position.

To set COMBI Cooking

• Set the POWER SELECTOR to the 

(combi) position.

5. Set the time control by turning the timer knob and then the oven operate inselected cooking mode.

If turing the timer knob for less than 2 minutes, turn it past 2 minutes and then back to the desired time.

6. The oven will be turned off automatically when the timer point to “OFF”.

Then take out foods.

• To prevent the oven operating with the door open, your is fitted with safety door interlock switches. 

If you wish to inspect the food during the cooking time, simply open the door. The oven will auto matically stop the
cooking. To continue cooking, you simply close the door.

• If you wish to sotp the cooking during the cooking simply turn the timer knob the point “OFF” Cooking can be reset at

any time during the cooking cycle by only turning the timer knob.

• Do not let the timer continue to operate after removing food. 

7. NOTE : When using the GRILL (KOG:368(9)OS) mode;

• Do not open the door so often, the temperature inside the oven decrease and the cooking may not complete in setting time.
• Never touch the oven window and metal interior of the oven when taking food in and out, because of the temperature

inside the oven and door is very high.

• When using these modes, be careful as the tray will be hot to touch, use oven gloves or pot holders while handling tray.

COOKING UTENSILS

Before use, the user should check that tensils are suitable for use in microwave ovens.

SYMBOL

POWER LEVLE

POWER

DEFORST

33%

MED-HIGH

77%

HIGH

100%

Material

Grill

Microwave

cooking

cooking

Glass (general)

NO

Yes(1)

Glass (heat resistant)

Yes

Yes

Glass-ceramic and ceramic(heat resistnat)

Yes

Yes(1)

Earthenware

Yes

Yes

China(heat resistant)

Yes

Yes

Plastic(general)

No

Yes(2)

Plastic(heat resistant)

Yes(2)

Yes(2)

Aluminium foil containers/aluminium foil

Yes

Yes(3)

Metal baking tins

Yes(4)

No 

Metal (pots. pans, etc)

Yes

No

Paper

No

Yes

1. Without metal parts or metal trims.
2. Some plastics are heat-proof only to certain temperatures. Check carefully!
3. It is possible to use aluminium foil to shield delicate areas of food (this prevents over-cooking).
4. Metal tins can be used in the combination methods, however if these are very deep, they will greatly reduce the efficiency, as

metal shields the microwave energy from the food.

Содержание KOG-3605































Отзывы: