Daewoo DSL15M1TC, Руководство по обслуживанию

Страница: 22 / 82

Pin Name No I/O Description
VID_DATA_IN_8
VID_DATA_IN_9
VID_DATA_IN_10
VID_DATA_IN_11
VID_DATA_IN_12
VID_DATA_IN_13
VID_DATA_IN_14
VID_DATA_IN_15 145
146
147
148
149
150
151
152 IO Input Pr / Pb Data in case of 16 Bit Video Input (CCIR601) of Video Input – 1
OR Input Green Data in case of 24 Bit Video Input
VID_DATA_IN_16
VID_DATA_IN_17
VID_DATA_IN_18
VID_DATA_IN_19
VID_DATA_IN_20
VID_DATA_IN_21
VID_DATA_IN_22
VID_DATA_IN_23 123
124
125
128
129
130
131
132 IO Input Blue Data in case of 24 Bit Video Input
OR Video Input – 2 in 8-bit with Embedded Sync / Separate Sync Sync in which case
VID_DATA_IN_16 acts as the LSB of the 8-bit Video input and VID_DATA_IN_23 acts as the MSB of
the 8-bit Video input.
VID_CLK2 118 I Video port data clock input meant for Video Input – 2. Up to 75Mhz
[Input, 5V-tolerant]
VID_DE/FLD 115 I Video Active Signal Input or the Field Signal Input from external Digital Video Source.
Note: In case of Multiple Digital Video Input Sources, only one source could be in 8-Bit with
embedded Sync (BT656 mode) format.
Table 5: System Interface
Pin Name No I/O Description
RESETn 10 I Hardware Reset (active low) [Schmitt trigger, 5v-tolerant]
Connect to ground with 0.01uF (or larger) capacitor.
TEST 20 I For normal mode of operation connect this Pin to Ground.
GPIO15 21 IO This pin is available as a general-purpose input/output port. Also it is optionally programmable to
give out the external chip select signal meant for external SRAM. Refer to note below.
HSYNC2 22 I Horizontal Sync signal Input-2. Used when Analog RGB component signal carries separate
HSYNC signal.
VSYNC2 23 I Vertical Sync signal Input-2. Used when Analog RGB component signal carries separate VSYNC
signal.
HOST_SCLK 24 IO Host input clock or 186 UART Data In or JTAG clock signal.
[Input, Schmitt trigger, 5V-tolerant]
HOST_SDATA 25 IO Host input data or 186 UART Data Out or JTAG mode signal.
[Bi-directional, Schmitt trigger, slew rate limited, 5V-tolerant]
DDC_SCLK 26 IO DDC2Bi clock for VGA Port [internal 10K
Ω
pull-up resistor]
DDC_SDATA 27 IO DDC2Bi data for VGA Port [internal 10K
Ω pull-up resistor]
MSTR_SCLK 30 O Clock signal from Master Serial 2 Wire Interface Controller
MSTR_SDATA 31 IO Data signal meant for Master Serial 2 Wire interface Controller
TCK 34 IO This Pin accepts the Input Clock signal in case of Boundary Scan Mode.
TDI 35 IO This Pin accepts the Input Data signal in case of Boundary Scan Mode.
TMS 36 IO This Pin accepts the Input Test Mode Select signal in case of Boundary Scan Mode.
TRST 37 IO This Pin accepts the Boundary Scan Reset signal in case of Boundary Scan Mode.
GPIO6/IRin 38 IO Input from Infra Red Decoder can be connected to this Pin. When not used, this pin is available
as General Purpose Input/output Port.
GPIO7/IRQin 41 IO Input Interrupt Request signal can be connected to this Pin. When not used, this pin is available
as General Purpose Input/output Port.
GPIO8/IRQout 42 IO This Pin will give out the Interrupt Signal to interrupt external Micro. When not used, this pin is
available as General Purpose Input/output Port.
GPIO9/SIPC_SCLK 43 IO This Pin accepts the Clock signal from External Serial 2 Wire interface Bus if FLI8125 is
programmed to be in Slave mode. When not used, this pin is available as General Purpose
Input/output Port.
GPIO10/SIPC_SDATA/
A18 44 IO This Pin acts as the Data I/O signal when used with External Serial 2 Wire interface Bus if
FLI8125 is programmed to be in Slave mode. Or this Pin is programmable to give out Address #
18 from the Internal Micro when used with 512K External Memory. When not used, this pin is
available as General Purpose Input/output Port.
GPIO11/PWM0 47 IO This Pin can be programmed to give out Pulse Width Modulated Output Pulses for external use.
When not used, this pin is available as General Purpose Input/output Port.
GPIO12/PWM1 48 IO This Pin can be programmed to give out Pulse Width Modulated Output Pulses for external use.
When not used, this pin is available as General Purpose Input/output Port.
GPIO13/PWM2 51 IO This Pin can be programmed to give out Pulse Width Modulated Output Pulses for external use.
When not used, this pin is available as General Purpose Input/output Port.