background image

24

1. Press the ON/OFF button of timer on the remote control to set the on timer mode, “HOUR” and “ON” on the remote display will be displayed and

“TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time. Then, if pressing “ENTER/CANCEL” button, ON TIMER
Mode will be started. If you want to stop ON TIMER Mode, please press “ENTER/CANCEL” again.

TO SET THE ON TIMER MODE

This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 12, 16, 20, 24.

2. While the unit is off, press the

TIMER ON button; the display will
light waiting input for the timer, but
the actual unit will not turn on.

3. Repeatedly press the TIMER ON  button

until the desired hour that you want the
unit to turn on appears on the display.
For example, if it is 1:00 P.M. and you
want the unit to turn on at 4:00 P.M., select 3 hours.

4. Press the ENTER button to input the setting

into memory; the unit will beep, the TIMER
indicator will light on the unit and the TIMER
indicator on the remote will light to indicate
the unit is in the timer mode.

5. Place the remote controller so it is facing the unit. When the de-

sired hour is reached, the unit will turn on to the selected mode.

AUTO

NOTE:

Press the ENTER button within 5 seconds of
selecting the desired time. If mote than 5 sec-
onds elapse, steps 3 and 4 must be repeated.

2. Press the TIMER OFF button once

to enter the Timer screen.

3. Repeatedly press the TIMER OFF but-

ton until the desired hour that you want
the unit to shut off appears on the dis-
play. For example, if it is 8:00 P.M. and
you want the unit to turn off at 10:00 P.M., select 2 hours.

4. Press the ENTER button to input the set-

ting into memory; the unit will beep, the
TIMER indicator will light on the unit and
the TIMER indicator on the remote will
light to indicate the unit is in the timer mode.

1. Press the ON/OFF button of timer on the remote control to set the off timer mode, “HOUR” and “OFF” on the remote display will be displayed

and “TIMER” will be flicked. When you increase to press “ON/OFF” you will get desired time. Then, if pressing “ENTER/CANCEL” button,
OFF TIMER Mode will be started. If you want to stop OFF TIMER Mode, please press “ENTER/CANCEL” again.

TO SET THE OFF TIMER MODE

This unit can be set to automatically turn off after a predetermined amount of hours (up to 12) in the order of 0.5, 1, 1.5,
2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10, 11, 12.

AUTO

5. Place the remote controller so it is facing the unit. When the

desired hour is reached, the unit will turn off.

AUTO

NOTE:

Press the ENTER button within 5 seconds of se-
lecting the desired time. If mote than 5 seconds
elapse, steps 3 and 4 must be repeated.

Содержание DSB-071LH































Отзывы: