Daewoo D35S-2 Скачать руководство пользователя

Страница: 38 / 42

Vehicle Systems

Disassembly & Assembly

Hydraulic Oil Filter Assembly

Remove And Install Hydraulic Oil
Filter Assembly

Disconnect four oil lines (1).

Remove hydraulic tank cover (2).

Remove the oil filter from hydraulic tank cover.

NOTE :

The following steps are for installation of the

hydraulic oil filter assembly.

Install the hydraulic oil filter assembly in position
on hydraulic tank cover.

Install the hydraulic tank cover (2) with six bolts
and washers.

Connect four oil lines (1).

Fill hydraulic oil tank to the correct level. See the
Operation and Maintenance Manual.

Transaxle

Remove & Install Transaxle

Start By :

Remove mast *

Remove floor plate

Refer to the mast systems Disassembly &
Assembly section for further information.

Raise the machine until tires are approximately 1
to 2 inches off of the floor. Position the machine on
tooling (A).

NOTE :

Put identification marks on all wiring, hoses

and lines to assure proper installation.

Disconnect hoses (1) and brake tubes (2).
Loosen bolts (3) and remove pedal assembly (4).

IACD222P

IACD255P

Tools Needed

A B

Stand 2

Link Bracket

Содержание D35S-2











































Результаты поиска

Содержание D35S-2

Отзывы:

Похожие инструкции для D35S-2

Бренды по названию

Популярные бренды

Daewoo D35S-2, Разборка/Сборка

Результаты поиска

Содержание D35S-2

Отзывы:

Похожие инструкции для D35S-2

Бренды по названию

Популярные бренды