manualshive.com logo in svg

Daewoo D35S-2, Разборка/Сборка

Поделиться
Скачать
Daewoo D35S-2 Скачать руководство пользователя страница 34

Vehicle Systems

Disassembly & Assembly

Hydraulic Pump

Remove and Install Hydraulic Pump

Start By :

a. 

Remove counterweight.

1. 

Drain the oil from the hydraulic tank.

2. 

Disconnect three oil lines (1) from the pump
elbows.

3. 

Remove bolts (2) and disconnect U-Joint (3).

4. 

Fasten a hoist to pump (5). Remove bolts (4) that
hold the pump in place. Remove the pump and
plate assembly. The weight of the pump is 

30 kg

(132 lb)

.

NOTE : 

The following steps are for installation of the

hydraulic pump.

5. 

Inspect seals for damage. Install new seals, if
needed.

6. 

Fasten a hoist to pump (5). Put the pump and
plate assembly in position and install the bolts that
hold the pump in place. The weight of the pump is

30 kg (132 lb)

.

7. 

Connect three oil lines (1) to the pump elbows.

8. 

Connect U-joint (3) in position and install bolts (2).

9. 

Fill the hydraulic tank with oil to the correct level.
See the Operation and Maintenance Manual.

End By :

a. 

Install counterweight

33

IACD237P

IACD238P

1

5

4

2

3

Содержание D35S-2











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды