background image

Maintenance

PREVENTIVE MAINTENANCE SCHEDULE

Service task  

Every month

Every 3 months

Every 6 months

Every 12 months in use

When worn

Check cable / replace cable when jacket is damaged

x

Check cable seal

x

Check pipes, hoses, valves

x

Check float switch / Level sensor function

x

Check for external damage, loose parts

x

Oil check * 

x

x

Oil change after 6 months or when contaminated with water

x

x

Check wear parts / adjust impeller and diffusor if necessary

x

x

Change wear parts

x

Replace seals

x

x

Replace ball bearings

x

x

Check contactor function

x

Stator measurement **

x

x

Measure thermal switches of stator

x

*) in continuous operation check every 3 months. At intermittent duty check oil every 6 months.
**) check related country standard and regulation.

EXTERNAL DAMAGE, LOOSE PARTS

Make sure that all screws, bolts and nuts are tight.

Check the condition of the pump lifting handle and

replace if damaged or worn. Replace any external part

that appears worn or damaged.

MOTOR INSULATION RESISTANCE

Use a 500 V DC Megger and measure the insulation

between the phases and between any phase and

ground. Resistance values should be over 1 M ohm. If

abnormal readings are obtained, immediately hand

the pump in for repair.

Also observe any local requirement regulations. The

stricter one will prevail.

IMPELLER

Inspect the impeller by removing the strainer and dif-

fusor. Replace the impeller if it is damaged or severe-

ly worn.

POWER CABLE

Inspect the cable for cuts, scrapes or sharp bends. If

the outer jacket is damaged, replace the cable. Do not

make splices within wet wells.

CABLE ENTRY

Make sure that the cable entry flange and strain relief

clamp are tight. If the cable entry is showing signs of

leakage replace the cable seal and position on the ca-

ble.

1

3

Содержание Sonora S330






























Отзывы: