background image

5

Verifying the Operation

Connect power to the electrical receptacle. 

Operate the appliance as outlined in the Use & 

Care Manual, that accompanied this product.

Connecting the Electrical Power

WARNINGS:

1.  Verify that the proper electrical 

power supply has been 

provided.

2.  Verify that the electrical supply 

matches the ratings found on 

the appliance data plate before 

proceeding.

3.  Be certain that power to the 

electrical receptacle has been 

disconnected, then plug the 

appliance into the electrical 

receptacle. 

4.  This appliance must be 

connected to a grounded, 

metallic, permanent wiring 

system. Alternatively, a 

grounding conductor should 

be connected to the grounding 

terminal or lead on the 

appliance. Failure to do so 

may result in an electrical 

shock hazard.

Three-Prong Plug

Three-prong grounded receptacle 

and cover plate

Grounding Instructions

The appliance is supplied with a four (4) foot 

long power cord terminated by a three-prong 

plug. The appliance power cord is intended to be 

plugged directly into a wall-mounted electrical 

receptacle. The correct voltage, frequency and 

amperage must be supplied to the electrical 

receptacle from a grounded, single phase circuit 

that is protected by a properly sized circuit 

breaker or time-delay fuse. The required voltage, 

frequency and amperage ratings are listed on the 

product data plate (located on the bottom of the 

chassis on the left side).

Slide Product Into the Cutout

•   Carefully, slide the unit into the 

opening. Be careful not to entangle 

power cord.

•   Make certain that the chassis is even 

with the adjacent cabinetry.

•   Check again to be sure the unit is 

level.

Leveling

•   Use an adjustable wrench to turn the 

leveling legs and raise or lower the 

product.

•   Adjust carefully; the product should 

be level and plumb with cabinetry, 

and should align with adjacent 

toekick height.

Turn Right to Lower

Turn Left to Raise

If you did not reverse the door swing:

•   Select the hinge cover marked “R” or 

“L”, depending on door swing.

•   Peel backing off the tape inside the 

decorative hinge cover. Press and 

snap into position.

•   Snap the screw hole cover into place 

on the opposite side.

5.  Do not use an extension cord 

with this appliance. Such use 

may result in fire, electrical 

shock, or other personal 

injury.

6.  Do not install a fuse in the 

neutral or ground circuit. A 

fuse in the neutral or ground 

circuit may result in an 

electrical shock hazard.

Содержание Wine Steward/Beverage Cooler









Отзывы: