20
2.
Safety Beams
Safety Beams are used for the early detec on of an object obstruc ng the closing door that could result in
damage or injury. While Safety Beams will detect most obstruc ons including cars, people and pets, it may not
necessarily detect all obstacles but will greatly reduce the risk. It is highly recommended that Safety Beams are
fi ed when automa ng a garage door.
For the purposes of the wiring diagram DuraOp cs Wireless Safety Beams (code DOPT03) are shown.
Refer to ‘Enable or Disable Safety Beams....Menu 3’ for programming.
3.
Electric and Magne c Locks
An automated door must not be locked using a padlock as both the door and the operator could be damaged
should the operator be triggered while the door is locked.
If extra security is required the door can be locked using either an Electric Lock (strike lock) or a Magne c Lock
(power lock) and controlled by the operator.
Refer to ‘Enable or Disable Electric/Magne c Lock....Menu 6’ for programming.
LUX DC12
Control Board
OR
NO
COM
DACE
Relay Module
Code: SA001
NO
COM
DACE
Relay Module
Code: SA001
Electric Lock
Magne c Lock
External
Power
Supply
+ve
-ve
Operator
Ba ery
+ve
-ve
A er connec ng the lock, it is important to select the correct lock type in the operator’s Programming Menu,
as selec ng the wrong lock type may cause damage to the lock or cause the lock to func on incorrectly.
PL
- Magne c / Power Lock
EL
- Electric / Strike Lock
REV
LIMITS
AUX LOCK 12V TRIG INF GND
Power
Input
LUX DC12
Control Board
DuraOp cs Wireless
Safety Beams
REV
LIMITS
AUX LOCK 12V TRIG INF GND
NO
GND
COM
12V/
24V
NC
FET
Power
Input
Cau on
:
When fi ng a Magne c Lock to the door, no NOT use the power from the operator as the lock will drain the
operator’s ba ery power.
Only use an external source to power the Magne c Lock.
Transformer Input Voltage
220 - 240V AC @50Hz
Output Voltage: 16VAC
Board Input Supply
12 - 18V AC or 17 - 22V DC
Motor Voltage
12V
Motor Power (Rated)
150W
Maximum Holding Capacity
1200N
Maximum Push/Pull Force
50kgF
Ba ery
12V DC
Maximum Daily Opera ons
(or in standby *)
*
Opera ons in standby is dependent on
charge level of ba ery and dura on of
power loss.
The number of opera ons is calculated
using a 12V 5Ah ba ery. Using a bigger
Ah rated ba ery will increase the
opera ons in standby and standby
dura on but will not allow for more daily
opera ons.
Push/Pull Force
Opera ons (Cycles)
10kgF
110 (55)
20kgF
86 (43)
30kgF
62 (31)
40kgF
40 (20)
50kgF
16 (8)
Opera ons: either Open
or
Close
Cycles: both Open
and
Close
Maximum Door Size
15m
2
Travel Speed
Note: Travel speed is dependent on load
and ba ery voltage.
8.5m/min
Outputs
Auxiliary: Adjustable to be either a light, trigger, status or low
ba ery indicator.
Lock: Adjustable to func on with either an electric or
magne c lock.
Inputs
External Trigger and Beams
Features
Programmable Limits
Adjustable Force Se ngs
Infrared Beam Input
Lock Output
Auxiliary Output: Light,
Trigger, Door Status or
Ba ery Status
Trigger Input
Holiday Lockout
Single Remote Erase
Up to 64 Programmable
Remotes
Remote Bu ons can be set to
ac vate the light or lockout
func ons individually
Adjustable Auto Close Func on
TECHNICAL SPECIFICATIONS
5
