background image

10375

A Milestone AV Technologies Brand

3100 North Detroit Street 
Warsaw, Indiana 46582 
P: 574.267.8101 or 800.622.3737 
F: 574.267.7804 or 877.325.4832 
E: [email protected] 
www.da-lite.com

DL–0634  01.16 
© 2016 Milestone AV Technologies LLC. Printed in U.S.A.

LIMITED TEN YEAR WARRANTY ON DA-LITE POLACOAT IN-WALL REAR PROJECTION SCREENS

Milestone AV Technologies LLC warrants this Da-Lite branded product to the original purchaser only, to be free 
from defects in materials and workmanship for a period of ten (10) years from the date of purchase by the original 
purchaser; provided they are properly operated according to Da-Lite’s instructions and are not damaged due to 
improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, 
or which has been tampered with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of 
the merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return 
the screen or part to Da-Lite, transportation expenses to and from 
Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment. 

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL 
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND 
MERCHANTABILITY. 

Any implied warranties of fitness for use, or merchantability, that may be mandated by statute 

or rule of law are limited to the ten (10) year warranty period. This warranty gives you specific legal rights, and you 
may also have other rights, which vary from state-to-state.  

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES 
OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, 
DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer 
Care Specialists at 3100 North Detroit Street, Warsaw, IN 46582, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE 
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE 
WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Содержание Polacoat Da-Plex Semi-Rigid













Отзывы: