background image

2

Important Safety Instructions

Pre-Installation

When using your video equipment, basic safety precautions 
should always be followed, including the following:

1.  Read and understand all instructions before using.

2.  Position the cord so that it will not be tripped over, pulled, or 

contact hot surfaces.

3.  If an extension cord is necessary, a cord with a current rating at 

least equal to that of the appliance should be used. Cords rated 
for less amperage than the appliance may overheat.

4.  To reduce the risk of electric shock, do not disassemble this 

appliance. Contact an authorized service dealer when repair 
work is required. Incorrect reassembly can cause electric shock 
when the appliance is used subsequently.

5.  The use of an accessory attachment not recommended  

by the manufacturer may cause a risk of fire, electric shock,  
or injury to persons.

Save These Instructions

This unit must be installed in accordance with the requirements 
of the Local Building Codes, the Canadian Electrical Code (CEC), 
CAN/CSA C22.1 and the National Electric Code (NEC) NFPA 70.

1.  Carefully unpack Da-Lift projector lift.

2.  Make sure to recheck measurements of projector lift location 

before installation.

Original Instructions

Disclaimer

Milestone and its affiliated corporations and subsidiaries 
(collectively "Milestone"), intend to make this manual accurate 
and complete. However, Milestone makes no claim that the 
information contained herein covers all details, conditions or 
variations, nor does it provide for every possible contingency in 
connection with the installation or use of this subject to change 
without notice or obligation of any kind. Milestone makes no 
representation of warranty, expressed or implied, regarding the 
information contained herein. Milestone assumes no 
responsibility for accuracy, completeness or sufficiency of the 
information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies. 
All rights reserved.

Содержание Da-Lift 10M









Отзывы: