Weight
Net weight: 3.5 kg
Net weight: 2.8 kg
Net weight: 2.8 kg
Dimensions
(L x W x H)
436 mm x 346 mm x 30 mm
436 mm x 346 mm x 30
mm
433 mm x 346 mm x 30 mm
The CR2032 lithium battery is used in the M8614/M8610/M8606-CM II. There is a risk of explosion if battery is
replaced by an incorrect type. Dispose of used batteries in a proper way.
M8610/M8606-CM III
The M8610-CM III is the primary management module of the RG-S8610; M8606-CM III is the primary management
module of the RG-S8606.M8610/M8606-CM III performs such functions as system switching, system status control, route
management, user access control and management, and network maintenance. Inserted in slots M1 and M2 in the middle
of the chassis, the management module supports active/standby redundancy, hot backup and hot swapping.
In the system, there must be at least one M8610/M8606-CM III for the system to work properly. However, you are
recommended to configure this module for both slots for higher reliability.
Module Appearance
Figure 1-16 Appearance of the M8610-CM III
Figure 1-17 Appearance of the M8606-CM III
External Interface
The M8610/M8606-CM III module provides three external interfaces:
USB (Universal Serial Bus) interface: By connecting the USB interface, USB storage devices can keep logs, host
version, alarms and other diagnosis information, facilitating online upgrade of switch software and log saving.
To secure data and prevent damage to the device, it is recommended to use qualified USB disk. The USB interface
of the RG-S8600 is compatible with most USB controllers. Some models of USB disk may not be identified. You are
recommended to use Patriot and Start-net Digital USB disks.
SD (Secure Digital Memory Card) interface: By connecting the SD interface, SD memory cards can keep logs, host
version, alarms and other diagnosis information, facilitating online upgrade of switch software and log saving.
To secure data and prevent damage to the device, it is recommended to use qualified SD memory cards. The SD
interface of the RG-S8600 is compatible with most SD memory cards. Some models of SD memory card may not be
identified.
Console port: As the serial communications port, it uses the RS-232 interface level and standard RJ-45 connector.
This port is used to connect the serial port of terminal computers running on the background for such tasks as
system debugging, configuration, maintenance, management, and host software loading.
10/100/1000M MGMT port: As the 10/100/1000BASE-T Ethernet port, it uses the RJ-45 connector. This port can be
used to connect the Ethernet port of the background computer for loading programs. When it is connected to the
Ethernet port of the background computer, the standard network cable can be used.
Reset button: As the reset button for the entire device, it resets the entire system.
There are long pressing and short pressing for the Reset button. If you press the button and hold it for less than five
seconds, it is short pressing; if you press the button and hold it for five seconds or longer, it is long pressing.
Indication of the Status LED for long pressing and short pressing: For short pressing of the button, the Status LED
flashes in green, and the board resets within five seconds at release. For long pressing of the button, the Status LED
flashes in green and then flashes in red; the board resets within five seconds at release.
LED
Содержание RG-S8614
