D-Link DSL-502T Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 91

background image

DSL-502T ADSL Router User’s Guide

Configure Connection 1 for Static IP for WAN

Static is used whenever a known static IP is assigned. The accompanying information such as the Subnet mask
and the gateway should also be specified in order to be able to connect. Up to three Domain Name Server (DNS)
addresses can also be specified. These are the servers would enable you to have access to other web servers.
Valid IP addresses range from 1.0.0.1 to 253.255.255.254.

Figure 3-8. Setup – Configure Connection 1 for Static IP for the WAN

To configure the WAN connection for Static, perform the steps listed below. Some of the settings do not need to
be changed the first time the device is set up, but can be changed later if you choose.

1. Click

the

Connection 1

button under

WAN Setup

to view the default

PPPoA Connection Setup

configuration menu.

2. Select

Static

from the

Type:

pull-down menu. This action will change the menu so it offers different

settings for configuration.

3. Type in a

Name:

in the space provided (

conn_1_Static_8_35

is used in the above example).

4. If you are told to change the

VPI

or

VCI

values, type in the values given to you by your service

provider. Many users will be able to use the default settings.

5. Leave

the

default

QoS

values if you are unsure or the ISP did not provide this information.

6. Do not change the

PCR

or

SCR

values unless you are required to do so. If you are told to change these,

type in the values given to you by your service provider.

7. The

Encapsulation

values LLC (SNAP) and VC (MUX) are two different methods of encapsulating

the PPP packet. Contact your ISP to make sure which encapsulation is being supported.

8. Based on the information provided by your ISP, enter the

IP Address

, Subnet

Mask

,

Default Gateway

(if provided), and Domain Name Services (

DNS

) values (if provided).

9. Select the desired

Mode

,

Bridged

or

Routed

.

23

«
...
37
38
39
40
41
...
»

Содержание DSL-502T




























































































Отзывы:

Нет отзывов

Похожие инструкции для DSL-502T

Бренд: ABB Страницы: 66

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Бренд: DCE Страницы: 5

Бренд: Oracle Страницы: 24

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Бренд: XMOS Страницы: 6

Бренд: Edgewater Networks Страницы: 7

Бренд: Rosewill Страницы: 3

Бренд: QuickLink Страницы: 8

Бренд: SurfControl Страницы: 2

Бренд: NKE Страницы: 15

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

Бренд: Foxconn Страницы: 1

Бренд: TP-Link Страницы: 2

Бренд: JETWAY Страницы: 15

Бренд: Actelis Networks Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды