manualshive.com logo in svg

D-Link DSL-502T, Руководство пользователя

Поделиться
Скачать
D-Link DSL-502T Скачать руководство пользователя страница 41

DSL-502T ADSL Router User’s Guide

 

 

5. Leave 

the 

default 

QoS

 values if you are unsure or the ISP did not provide this information. 

6.  Do not change the 

PCR

 or 

SCR

 values unless you are required to do so. If you are told to change these, 

type in the values given to you by your service provider. 

7. The 

Encapsulation

 values LLC (SNAP) and VC (MUX) are two different methods of encapsulating 

the PPP packet. Contact your ISP to make sure which encapsulation is being supported. 

8. Click 

the 

Apply

 

button when you have entered all the information. The web browser will briefly go 

blank. You are now finished changing setting for the primary WAN connection known as Connection 1. 
It is now necessary to save the changes you just made and restart the Router.  

9.  To save the changes made to Connection 1, click the 

Tools

 tab and then click on the 

System 

Commands

 button. Click on the 

Save All 

button to store the configuration settings. Click on 

Back 

button to return to the System Commands menu. 

10.  Check the WAN connection status. Click the 

Status 

tab and then the 

Connection Status

 button. Look 

under 

WAN 

to view the 

State

 of Connection 1, it should read 

Connected

. If the WAN connection state 

does not appear to 

Connected

 after a few minutes, go back to the Connection 1 Setup menu, check the 

settings and make sure they are correct. 

Configure Connection 1 for CLIP 

CLIP or IPoA connections function in a similar way to DHCP or Static IP connections. Certain CLIP 
connections function like P2P networks. The router must obtain IP settings from a server owned by an ISP, or 
use a static IP address assigned by the ISP.   

 

Figure 3-10. Setup – Configure Connection 1 for CLIP (IPoA) 

To configure the WAN connection for CLIP, perform the steps listed below. Some of the settings do not need to 
be changed when you first set up the device but can be changed later if you choose. 

1. Click 

the 

Connection 1

 button under 

WAN Setup

 to view the default 

PPPoA Connection Setup

 

configuration menu. 

 

25

Содержание DSL-502T




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды