background image

Cyrus Mono X 200 Signature & Mono X 300 Signature 

User Instructions

6

Key to the front panel drawing

Standby key

1. 

Standby indicator

2. 

Input indicator

3. 

Input selector key 

4. 

OPERATION

Mono X

Zero Feedback

300

INPUT

c

a b

d

Power Control

When  power  is  first  applied,  the  amplifier  will  initialise,  then  set  to 
Standby.

Power control from the front panel

Press  the  STANDBY  key 

a

  briefly  to  switch  the  amplifier  between 

operational and standby modes. The Standby Indicator 

b

 will glow green 

when operational or red when set to Standby.

Music sensing automatic power control

Music sense power control can be enabled if required. 
To enable or disable Music sense, first set the amplifier to Standby, then 
press and hold the STANDBY key for two seconds. The Standby Indicator 
will flash red three times, then change colour to show the status of Music 
sense – orange when enabled or red when disabled.
When Music sense is enabled, the amplifier will switch on automatically if 
a music signal is detected from the pre-amplifier, and set to Standby after 
10 minutes of silence. The STANDBY key may also be used to switch the 
amplifier on if required, or to switch the amplifier back to Standby with 
Music sense enabled (Standby indicator will glow orange).
NOTE:  Standby  power  consumption  will  be  significantly  higher  when 
Music sense is enabled.
A  12V  trigger,  MC-BUS  or  RS232  ‘OFF’  command  cancels  the  Music 
sense function.

Input Indicator

The  INPUT  Indicator 

c

  will  glow  red  when  the  output  of  the  Mono  X 

Signature  is  muted. This  occurs  for  a  few  seconds  following  Standby 
operation or if a temporary overload condition arises. If the INPUT Indicator 
flashes at any time, refer to the Troubleshooting Guide.

Selecting an Input

The  front  panel  INPUT  key 

d

  selects  RCA  Phono  or  Balanced  input 

connection. To change inputs, the amplifier must be switched on.
Press  and  hold  the  INPUT  key 

d

  until  the  INPUT  indicator 

c

  changes 

colour as shown.

INPuT Indicator colour

Input selected

Green

Balanced

Orange

RCA Phono

NOTE:  The  input  setting  will  be  retained  when  mains  power  is 
disconnected.

Содержание Mono X 200 Signature













Отзывы: