background image

Document #: 001-52039  Rev. **

Revised March 02, 2009

Page 23 of 23

AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document are the trademarks of their respective

holders.

 STK17TA8

© Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. 

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress. 

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges. 

Use may be limited by and subject to the applicable Cypress software license agreement. 

Document History Page

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office

closest to you, visit us at 

cypress.com/sales.

Products

PSoC

psoc.cypress.com

Clocks & Buffers

clocks.cypress.com

Wireless

wireless.cypress.com

Memories

memory.cypress.com

Image Sensors

image.cypress.com

PSoC Solutions

General

psoc.cypress.com/solutions

Low Power/Low Voltage

psoc.cypress.com/low-power

            

Precision Analog 

psoc.cypress.com/precision-analog

LCD Drive

psoc.cypress.com/lcd-drive

CAN 2.0b

psoc.cypress.com/can

USB

psoc.cypress.com/usb

Document Title: STK17TA8 128k X 8 AutoStore™ nvSRAM with Real Time Clock 

Document Number: 001-52039

Rev. ECN No.

Orig. of 

Change

Submission 

Date

Description of Change

**

2668660

GVCH/PYRS

03/04/2009

New Data Sheet

[+] Feedback 

Содержание AutoStore STK17TA8
























Отзывы: