PSoC 6 WiFi-BT Pioneer Kit Guide, Doc. # 002-22677 Rev. *B
41
Kit Hardware
battery are not included in the kit and should be purchased separately if you want to test the
battery charging functionality.
3. KitProg2 USB connector (J10):
The USB cable provided along with the PSoC 6 WiFi-BT
Pioneer Kit connects between this USB connector and the PC to use the KitProg2 onboard
programmer and debugger and to provide power to the Pioneer board.
J10
is also used for the
USB Type-C power delivery system. See
“EZ-PD CCG3 Type-C Power Delivery”
for
more details.
4. Cypress EZ-PD CCG3 Type-C Port Controller with PD (CYPD3125-40LQXIT, U3):
The
Pioneer board includes an EZ-PD CCG3 USB Type-C port controller with power delivery system.
This device is pre-programmed and can deliver power from a Type-C port to an onboard header
J16
, while simultaneously charging a lithium-ion polymer battery connected to
J15
. In addition,
the power delivery system can deliver power to a Type-C power sink or consumer, such as a
mobile phone, with the power derived from the VIN supply. See
for more details.
5. KitProg2 programming button (SW3):
This button can be used to switch between the KitProg2
operation modes (proprietary SWD programming/CMSIS-DAP mode). This button can also be
used to provide input to the PSoC 5LP in custom application mode. For more details, see the
.
6. KitProg2 I/O header (J6):
This header brings out several GPIOs of the onboard KitProg2
PSoC 5LP device. This includes the USB-I2C, USB-UART, and USB-SPI bridge lines. The
additional PSoC 5LP pins are direct connections to the internal programmable analog logic of the
PSoC 5LP. You can also use these pins for custom applications. For more details on KitProg2,
see the
.
7. KitProg2 programming/custom application header (J7):
This header brings out more GPIOs
of the PSoC 5LP, which can be used for custom applications. It also contains a five-pin SWD
programming header for the PSoC 5LP.
8. External power supply VIN connector (J9):
This connector connects an external DC power
supply input to the onboard regulators and the USB Type-C power delivery system. The voltage
input from the external supply should be between 5 V and 12 V. Moreover, when used as an input
to the USB Type-C power delivery system, the external power supply should have enough
current capacity to support the load connected via the Type-C port. See
for more details.
9. PSoC 6 MCU user button (SW2):
This button can be used to provide an input to PSoC 6 MCU.
Note that by default the button connects the PSoC 6 MCU pin to ground when pressed, so you
need to configure the PSoC 6 MCU pin as a digital input with resistive pull-up for detecting the
button press. This button also provides a wake-up source from low-power modes of the device.
10.KitProg2 application selection button (SW4):
This button can be used to switch between
KitProg2 programming mode and custom application mode. For more details, see the
.
11. Digilent Pmod-compatible I/O header (J14):
This header can be used to connect Digilent
Pmod 1 x 6 pin modules.
12. Power LED (LED4):
This is the amber LED that indicates the status of power supplied to
PSoC 6 MCU.
13. Kitprog2 status LEDs (LED1, LED2, and LED3):
Red, amber, and green LEDs (LED1, LED2,
and LED3 respectively) indicate the status of KitProg2. For more details on the KitProg2 status,
see the
14. PSoC 6 MCU reset button (SW1):
This button is used to reset PSoC 6 MCU. It connects the
PSoC 6 MCU reset (XRES) pin to ground.
15. PSoC 6 MCU I/O headers (J18, J19, and J20):
These headers provide connectivity to PSoC 6
MCU GPIOs that are not connected to the Arduino-compatible headers. Most of these pins are
Содержание CY8CKIT-062-WiFi-BT
Страница 44: ...PSoC 6 WiFi BT Pioneer Kit Guide Doc 002 22677 Rev B 44 Kit Hardware Figure 4 5 Pioneer Board Pinout...
Страница 63: ...PSoC 6 WiFi BT Pioneer Kit Guide Doc 002 22677 Rev B 63 Figure A 4 Schematics of Power Supply System...
Страница 72: ...PSoC 6 WiFi BT Pioneer Kit Guide Doc 002 22677 Rev B 72...