CYP CSC-200P, Руководство пользователя

Страница: 9 / 12

9 7
(7). RS-232 Control of the CSC-200P Video Scaler
The Video Input selection and signal parameter setting for the CSC-200RS can
also be controlled via an external control system by using the RS-232 port on the
unit. If information for this control method is required,beyond the scope of the
instructions provided in this section, please contact Cypress Technology Support,
A disk is provided with the CSC-200RS containing a sample Windows Control Panel
that permits remote control of the unit from a PC via RS-232.
Note- The connection between the CSC-200RS unit and the RS-232 remote
controller is made with a modem cable.
* The Connection between video scaler and remote controller with RS-232
modem cable.
PIN
1
2
3
4
5
6
7
8
9
Definition
NC
T xD
R x D
NC
GND
NC
NC
NC
NC
PIN
1
2
3
4
5
6
7
8
9
Definition
NC
R xD
T x D
NC
GND
NC
NC
NC
NC
Video Scaler
Remote Controller


* RS-232 transmission format:
Baud Rate : 9600 bps
Data Bit : 8 Bits
Parity: None
Stop Bit: 1 bit
3
(4). Connecting the hardware
Front Panel
2. Picture: Press the button to toggle through picture adjust parameters as follows:
Contrast

Bright

Color

Tint

Sharpness

Contrast
Contrast: Press

or

to adjust contrast level. The range of adjustment is 0~63.
Factory default value is 58.
Bright: Press

or

to adjust Brightness level. The range of adjustment is 0~63.
Factory default value is 31.
Color: Press

or

to adjust color level. The range of adjustment is 0~63.
Factory default value is 31.
Tint: Press

or

to adjust NTSC Tint level. The range of adjustment is 0~63.
Factory defaults value is 31.
Sharpness: Press

or

to adjust sharpness level.
The range of adjustment is 0~63. Factory defaults at 10.
3.

,

: Press to toggle through various adjust controls or to alter setting value.
4. IR Sensor: Infrared remote control sensor.
5. Power and LED button: Press once to power on the unit, press again to turn off.
Note:
* Under picture adjust mode, press

and

simutaneously will revert the selected
parameter back to factory preset value. Press both buttons for over 5 seconds.
will revert all picture parameters back to their factory preset values.
* You can use RS-232 to lockout the front panel controls. To lift this lockout
and revert all parameters back to factory preset value, please press"mode"
and "picture" buttons simultaneously for over 10 seconds.
6. Front Panel Lockout- Under certain circumstances it may be desirable to disable
the front panel controls. For example, to prevent
unauthorized or accidental changes to the setting while the
unit is in use.
To disable the front panel controls use RS-232 to set the
front panel lockout to ON position.
6
(6). Remote Control
1. Power: Power ON/OFF button.
2. Display: Press the button to enable or disable the on screen display
of the resolution information.
3. C-Video: Press the button to select composite video as input source.
4. S-Video: Press the button to select S-Video as input source.
5. YCbCr: Press the button to select YCbCr as input source.
6. PC: Press the button to select PC input looping through to the output.
7. VGA: Press the button to select 640 x 480 as output resolution.
8. SVGA: Press the button to select 800 x 600 as output resolution.
9. XGA: Press the button to select 1024 x 768 as output resolution.
10. SXGA: Press the button to select 1280 x 1024 as output resolution.
11. 480p: Press the button to select 852 x 480p as output resolution.
12. 576p: Press the button to select 852 x 576p as output resolution.
13. 720p: Press the button to select 1280 x 720p as output resolution.
14. 1080i: Press the button to select 1920 x 1080i (interaced) as output resolution.
15. Aspect ratio: Press the button to switch between standard, 4:3 and
wide (16:9)aspect ratio.
16 IR-Set: When IR sensor is turned off by RS-232, Press this button for
over 15 seconds will turn on the IR sensor.
17. 3D: Press to turn ON/OFF the 3D enhance.
18. NR: Press to turn ON/OFF digital noise reduction.
19. Mode: Same as "mode" button on front panel.
press to toggle through
Source

Resolution

Output

Aspect

3D Enhance

Digital NR

Source
20. Picture: Same as picture button on
front panel. Press to toggle
through Contrast

Bright

Color

Tint

Sharpness

Contrast
21. Reset: Press this button will revert picture
adjust back to factory preset value.
2 9 11 1
3
4
5
6
7
8
10
13
12
16
17
19
18
20
21
15
14
5 4
(5). Connecting and Installation (4). Connecting the hardware
Connecting the Video inputs
The video scaler can accept a composite video, an S-Video or a YCbCr input
signal for scaling, as well as a computer signal input that is passed through the unit
when the PC in (Bypass) is selected.
Rear Panel
1 . Composite Video: Use a Composite video cable to connect the composite video
output of the source equipment to the connector labeled
"C-Video" on the back of the Video Scaler.
2 . S-Video: Use a S-Video cable to connect the S-Video output of the source video
equipment to the connector labled " S-Video" on the back of the
Video Scaler.
S-Video provides improved performance over Composite Video and is
recommended over composite.
3 . YCbCr input: Use a 3 RCA-to-3 RCA YCbCr cable to connect the YCbCr output of
the source video equipment to the connectors labled YCbCr on the
back of the video scaler. Please note the plugs' color have to match
with the color of the RCA Jacks. YCbCr component provides the best
picture quality among all three inputs, and should be used whenever
possible.
4 . Computer RGB with H&V Sync: Connect the source computer's VGA output
signal to the HD 15 connector labled "PC In" on the
back of the Video Scaler.
Note: This Computer inputs signal is not sclaed, but is available for pass-through
when the Video Scaler is in the PC In (Bypass) mode.
Connecting the scaled output to your projector, PDP, or LCD Display
5 . The HD-15 D-Sub connector is shared by PC/RGBHV output and HDTV/YPbPr output.
When PC/RGBHV output resoultion (VGA to SXGA) is selected, use the HD-15 to
HD-15 VGA cable to connect the output to the PC input of your display monitor.
When HDTV/YPbPr output (480p, 576p, 720p, 1080i) is selected, use the HD-15 to
YPbPr 3 x RCA cable to connect the output to the YPbPr input of your HDTV display.
Note: Use of wrong cable for your selected output will result in an abnormal picture
on the screen.
6 . RS232: 9-pin D-sub connector for connecting to your PC or other control console for
remote control.
7 . DC power jack: 5V 2A DC power input.
2 1
3 4 5 7
6
INPUT
S-VIDEO VIDEO Y Cb Cr
PC IN
RGB/YPbPr
OUTPUT
DC 12V
+
RS 232
DC Adaptor
HDTV
Control In
INPUT
S-VIDEO VIDEO Y Cb Cr
PC IN
RGB/YPbPr
OUTPUT
DC 12V
+
RS 232
Rear Panel