Cygnus M3-DIVE Скачать руководство пользователя страница 104

Страница: 104 / 117

Cygnus DIVE Operating Manual

M3-DIVE-M-ENG_Iss9.docx

Page 104 of 117

22.

Technical Specifications

Cygnus DIVE Technical Specifications

General Attributes

Size

105 mm x 110 mm x 35 mm (W x H x D)
(4.1 in x 4.3 in x 1.4 in)

Weight In Air

Complete Gauge 905 g (2 lb.)

Gauge Body 557 g (1.22 lb.)
Battery 79 g (0.17 lb.)
Probe & Cable 269 g (0.6 lb.)

Power Supply

Rechargeable Lithium-Ion Battery

Probe Sockets

Fischer 105 Series

Operating Temperature Range -10°C to +50°C (14°F to 122°F)

Storage Temperature Range

-10°C to +60°C (14°F to 140°F)

Battery Operation Time

Approximately 10 hrs. continuous measurement with fully
charged battery pack.

Battery Voltage Range

Min 3.2 V dc, Max 4.5 V dc

Battery Type

Sealed Lithium-Ion rechargeable single cell. 8.1 Watt-hours.
Internally protected against short circuit and overcharge.

Low Battery Indication

Battery Level Indication on Display with Low Battery Warning
Message.

PRF

N/A

Monitor Outputs

N/A

Through Coating
Measurements

Through coating measurement in Multiple Echo mode only.
Coatings up to 3 mm thick as standard depending on coating
velocity.
Deep Coat mode provides ability to measure through thicker
coatings depending on coating material.

Materials

Sound Velocity from 2000 m/s to 9000 m/s
[0.0780 in/us to 0.3543 in/us]

Содержание M3-DIVE






















































































































Результаты поиска

Содержание M3-DIVE

Отзывы:

Cygnus M3-DIVE, Руководство по эксплуатации, Страница: 104 / 117

Результаты поиска

Содержание M3-DIVE

Отзывы: