CyberPower OL10000RT3UPDU Скачать руководство пользователя страница 27

 

Copyright ©  2017 CyberPower Systems, Inc.

 

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

 

 

 

26

 

 

Who Pays For Shipping?

 

We pay when we send items to you; you pay when you send items to us. 

What Are Some Examples Of What This Warranty Does Not Cover?

 

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of 
the failure or the restoration of data or records, or the reinstallation of software. 

2.  This  Warranty  does  not  cover  or  apply  to:  misuse,  modification,  operation  or  storage  outside  environmental  limits  of  the  Product  or  the  equipment 
connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or 
intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices, etc.

 

What Other Limitations Apply? 

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty. 

1. This Warranty does not apply unless the Product  and the  equipment  that was connected to it were connected to properly  wired and grounded outlets 
(including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors. 

2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product 
and not “daisy-chained” together in serial fashion with any extension cords, another Product or device similar to the Product, surge suppressor, or power tap. 
Any such installation voids the Limited Warranty. 

3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license, 
instruction manual, or warnings provided with the Product and the equipment connected to it. 

4. The Product must have been used at all times within the limitations on the Product’s VA capacity. 

The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses from lightning or other 
power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence will be deemed outside the rated capabilities of 
the Product and the Limited Warranty is void. CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following: 

1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software. 

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120 volt power lines in 
the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines, 
when properly installed and connected. (This exclusion applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or 
fluctuations, or by transients in such transmission.) 

3. Damage from any circumstance described as excluded above with respect to the Product. 

4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or the Connected 
Equipment. 

5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower excludes any liability 
for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the specific 
limited  agreement  of  CyberPower  to  provide  certain  warranty  benefits  regarding  "Connected  Equipment"  under  this  Warranty],  loss  of  profits,  business 
interruption, or loss of information or data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, 
so the above limitation may not apply to you. 

6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous environments requiring 
fail-safe performance, or for use in any circumstance in which the failure of the Product could lead directly to death, personal injury, or severe physical or 
property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities"). CyberPower expressly 
disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High 
Risk Activities or with Aquariums. 

ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.

 

Where Can I Get More Information?

 

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded. 

CyberPower is the warrantor under this Limited Warranty. 

For further information please feel free to contact CyberPower at CyberPower Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379; call us 

at (877) 297-6937; or send us an e-mail message at [email protected].

 

Содержание OL10000RT3UPDU





























Отзывы: