manualshive.com logo in svg

CustomWorks Dominator, Модель

Поделиться
Скачать
CustomWorks Dominator Скачать руководство пользователя страница 3

Diff Assembly

Diff Assembly

Diff Assembly

Diff Assembly

Diff Assembly

1229                 Qty 2
5/32 x 5/16 Bearing

1:1

4361      Qty 1
Diff Bolt Cover

-Parts for
 Step#1

4362          Qty 1
Diff Spring

4358      Qty 2
Diff Ring

3613        Qty 1
Right Outdrive

-Parts for
 Step#2

1:1

3609                Qty 1
Dominator Diff Bolt

1:1

4359   Qty 6
Thrust Balls

4360      Qty 2
Thrust Washer

3612     Qty 1
Left Outdrive

3615        Qty 1
Diff Pulley

4357        Qty 12
Diff Balls

4361        Qty 1
Diff T- Nut

Bag B

Bag B

Bag B

Bag B

Bag B

- Slide a 4360 Thrust Washer onto the 3609 Diff Bolt.

- Apply a thick layer of Diff Lube to the Thrust Washer, press
(6) 4359 Thrust Balls into the Diff Lube.

- Slide the other Thrust Washer on the Diff Bolt and insert it
into the 3613 Right Outdrive.

- Press (1) 1229 Bearing into the Outdrive.

- Put (1) 4358 Diff Ring on the Outdrive, apply Diff Lube as
shown.

- Put (1) 4358 Diff Ring onto the 3612 Left Outdrive, apply Diff
Grease as shown.

- Install the 4362 Diff Spring and 4361 T-nut into the Outdrive.

- Carefully slide the diff assembly together so the Diff Bolt passes
thru the entire assembly and threads into the T-nut.

- Screw the Diff Bolt into the T-nut until you feel the Diff Spring
fully compress. DO NOT OVERTIGHTEN!!! Back the Diff Bolt off
EXACTLY 1/8 of a turn. Diff motion should be smooth and the
Outdrives will turn in opposite directions.

- Press (1) 1229 Bearing and the (12) 4357 Diff Balls into the
Diff Pulley. Use Diff Lube as shown.

STEP #1

STEP #2

4361

3609

4359
   X6

4360

3613

1229

4358

3613

3615

4357
 X12 1229

4358

3612

4362

4361

CUSTOM-TIP!!!

CUSTOM-TIP!!!

CUSTOM-TIP!!!

CUSTOM-TIP!!!

CUSTOM-TIP!!!
  -Using 400 Grit Sandpaper in a“Figure 8”
      pattern, it is best to sand the surfaces
         of both the 4358 Diff Ring and 4360
            Thrust Washers. The textured
               surface results in a smoother and
                  longer lasting diff.

DIFF   LUBE

DIFF
  LUBE

DIFF

  LUBE

One-Way Assembly

One-Way Assembly

One-Way Assembly

One-Way Assembly

One-Way Assembly

3605              Qty 2
One-Way Outdrive

-Parts for
 Bag A

3602         Qty 1
One-Way Pulley

3601       Qty 1
One-Way Hub

1:1

3602      Qty 1
Pulley Ring

Bag A

Bag A

Bag A

Bag A

Bag A

5292              Qty 4
M2.5 x 4 BH Screw

3605

3601

3602
PULLEY

3602
RING

5292

3605

- Mount 3602 One-Way Pulley to the 3601 One-
Way Hub using (4) 5292 Screws.

- Attach the 3602 Pulley Ring to the One-Way
Pulley using 4-6 small dots of CA Glue where the
faces of the two parts meet.

- Slide 3605 One-Way Outdrives into the bear-
ings pressed into the One-Way Hub.

3615      Qty 1
Pulley Ring

- Attach the 3615 Pulley Ring to the
One-Way Pulley using 4-6 small dots of CA Glue
where the faces of the two parts meet.

* CA GLUE ALONG THIS FACE

*Apply CA Glue along the face of
the pulley as shown. 4-6 small
dots of glue will work.  DO NOT
allow glue to run into sprocket
teeth!

Содержание Dominator

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды