- Attach the 5241 Servo Extender to the 5242 Servo Saver using
5201 Screw. Mount the Steering Links to the Extender using the
hardware as shown above.
- Fasten the 5239 Servo Mounts to your servo using 5253 Screw
with (1) 5212 Washer on both sides of the servo tabs.
- Attach the servo to the chassis using 5263 Screws. Servo Saver
should be centered between the front end.
- Mount Camber Link Ball End to the Front Tower in the 2nd
hole from the top using 5254 Screw and 5205 LockNut.
- Insert the 7200 Axle into the
3202 Steering Arm so the
holes are in-line.
-Align the Steering Arm into
the 3205 Castor Block and
press the 7209 Ball Stud
Kingpin thru the assembly
as shown.
Rear Suspension
Rear Suspension
Rear Suspension
Rear Suspension
Rear Suspension
4234 Qty 2
Rear Inner Susp Pin
3240 Qty 2
Rear Susp Arm
2224 Qty 2
Top Plate Block
-Parts for
Step#1
2218 Qty 2
Camber Link Stand-Off
1:1
1289 Qty 1
INT SE Rear Tower
-Parts for
Step#2
1:1
5230 Qty 24
E-Clip
1:1
5263 Qty 2
4-40 x 3/8 FH Screw
1:1
5252 Qty 6
4-40 x 1/4 BH Screw
5264 Qty 6
4-40 x 1/2 FH Screw
2224
-Attach the 2224 Alum Blocks and 2218 Camber
Link Stand-Offs to the 1289 Rear Tower.
1289
2224
5252
2218
5252
STEP #2
-Attach the 3240 Susp Arm
to the 2222 Toe Block using
the 4234 Susp Pin.Retain
the pin with 5230 E-Clips.
-Mount Susp and Rear
Tower assemblies with
screws in the
locations shown.
-LEFT Side Assembly Shown.
FRONT
FRONT
-NOTE: Back side of Toe
Block for proper direction!
STEP #1
STEP #3
STEP #2
2222
5263
3240
5230
Bag C
Bag C
Bag C
Bag C
Bag C
5264
5264
4234
- Fasten 8122 Ball Stud to the Extender thru the
middle hole on the left assmebly, thru the inner
most hole on the right assembly.
- Mount the 1292 Steering Arm Extender to the
Steering Arm using 5253 Screw.
-Mount the 3203 Castor
Block to the Susp Arm by
inserting the 4241 Susp Pin
thru the Susp Arm, Spacer,
and Castor Block. Retain the
Susp Pin by attaching 5230
E-Clips to each end.
7209
5230
7200
3202
4241
1292
5205
5253
8122
5004
3203
5201
5241
5201
5242
5233
5204
5239
5212
5253
INNER MOST
HOLE.
5253
5263
THRU
CHASSIS
5254
5205
2222 Qty 2
1-3 Toe Block
- Use the remaining 7209 Spacers and E-Clip the
Ball Stud King pin to retain within the Castor
Block assembly.
*Optional Front End
Set-up Shown on the
bottom-left corner of Page
#9 allows for easier front
shock removal. *
5230
NOTE: The Servo Extender and it’s screws should be as close to the chassis
without hitting, use the extra nylon spacers to correctly mount your servo.
