INTRODUCTION
TPTCM
3
2
1
3
5
9
6
4
8
7
•
When the LINE FEED (6) key is pressed, the printer advances the paper so that it may be inserted
manually in the printing mechanism. During power-up, if the LINE FEED key is held down, the printer will
perform the FONT TEST routine. If it has the version with chinese simplified font GB2312 (option 0104) at
the end of the FONT TEST is printed all characters set (about 7000).
•
If the FORM FEED (5) key is enabled, when it is pressed the printer advances the paper the number of
increments programmed in the Eeprom. If the FORM FEED key is not enabled and the printer is in
Custom Emulation mode, when the key is pressed, the code $0C is transmitted on the RS232 serial
line. This function may be modified by the
$1B $3D
software command (see section on software
commands).
•
During power-up, if both keys are held down, the printer enters the print setup routine. Following the
print-out of the setup report, the printer remains in standby until a key is pressed or signals arrive from
the serial port; each 10 characters it prints out hexadecimal and ASCII codes (if the characters are
underlined, the receive buffer is full); see Receive buffer hexidecimal print-out.
•
To entry in the notch sensor autocalibration phase (printer option 0103) press the LINE FEED key during
the printer power-up. After the beginning of the font test press, at the same time, the LINE FEED key
and the FORM FEED key. At the end of the font test the printer begin the notch threshold
autocalibration.
•
The “Power On” LED (green) indicates that the printer is on.
•
The Paper Low LED (red) indicates that the paper is about to run out.
•
The “Status” LED (yellow) indicates printer status; the check is made on-line. Given in the table below
are the various LED signals and the corresponding printer status.
s
u
t
a
t
s
D
E
L
n
o
it
p
i
r
c
s
e
D
y
d
a
e
t
S
N
O
r
e
t
n
i
r
P
-
n
o
i
t
c
n
u
f
l
a
m
o
n
g
n
i
k
n
il
b
d
i
p
a
R
g
n
i
t
a
e
h
r
e
v
O
g
n
i
k
n
il
b
w
o
l
S
(
d
o
i
r
e
p
d
e
d
n
e
t
x
e
r
o
f
t
il
)
e
g
a
s
s
e
m
"
r
e
p
a
P
o
N
"
g
n
i
k
n
il
b
w
o
l
S
(
)
d
o
i
r
e
p
t
r
o
h
s
r
o
f
t
il
s
d
r
a
w
p
u
d
e
n
r
u
t
d
a
e
H
f
f
o
s
n
i
a
m
e
R
n
o
i
t
c
n
u
f
l
a
m
r
e
t
n
i
r
P
(Fig.1)
Содержание TPTCM
