Custom Audio Electronics RS-10 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 8

Custom Audio Electronics RS-10 Скачать руководство пользователя страница 6

Factory Default Settings for CAE RS-10

The factory settings for the RS-10 may be reset with the following procedure. WARNING!! This procedure will erase
all user programmed data.
1. With AC power off, press and hold switches PS-1 and PS-2 at the same time.
2. Apply AC power with both switches pressed. System will reset. Release both switches.
3. The RS-10 will now contain its factory settings.

NOTE: The factory default for patch changes is no patch changes set.

Factory Default Settings are as follows:

PC1

MIDI channel 1

PC 2

MIDI channel 2

PC3

MIDI channel 3

PC4

MIDI channel 4

PC5

MIDI channel 5

SW0

MIDI channel 15 Controller #9

SW1

MIDI channel 15 Controller #10

SW2

MIDI channel 15 Controller #11

SW3

MIDI channel 15 Controller #12

SW4

MIDI channel 15 Controller #13

SW5

MIDI channel 15 Controller #14

SW6

MIDI channel 15 Controller #15

SW7

MIDI channel 15 Controller #16

SW8

MIDI channel 15 Controller #17

SW9

MIDI channel 15 Controller #18

P 1

MIDI channel 1 Controller #1

P 2

MIDI channel 1 Controller #4

MIDI receive

channel 16

RS-10 MIDI Bulk Data Dump/Load Procedure

NOTE: Bulk Dump/Load can only be executed in normal (single footswitch) mode. Master/Slave Function = 1

To send data: (Bulk/Dump)
1. In PROGRAM MODE use FUNCTION SELECT switch (PS-1) to step through functions until display reads Snd.
2. Press program (PS-4) to send data out the MIDI port.
3. Display will flash indicating data is sent.

IMPORTANT: MIDI data dumped by the RS-10 must be sent as a sequence for accurate results. Example: Set
Alesis Data Disk SQ to RECV MIDI SEQ.

NOTE: CAE recommends the use of the Alesis Data Disk with SQ (Sequencer Software) for data storage. However,
most sequencers or computers with sequencing software will work.

To receive data: (Bulk/Load)
1. In PROGRAM MODE, use FUNCTION SELECT switch (PS-1) to step through functions until display reads rEc.
2. Press program (PS-4) switch. Display flashes.
3. The RS-10 is now ready to receive data from the storage device or computer via the MIDI in port.
4. Initiate the data dump procedure for the storage device (Data Disk, sequencer or computer).

The RS-10 display will stop flashing when the data is received. Exit FUNCTION SELECT mode by pressing bank UP
switch.

«
...
4
5
6
7
8
»

Содержание RS-10









Отзывы:

Нет отзывов