Curtis 3301T Скачать руководство пользователя страница 56

Страница: 56 / 63

6 — CANopen COMMUNICATIONS

Curtis Model 3301T Digital Instrumentation – September 2021

Return to TOC

pg. 50

TPDO1

Byte(s)

Description

The following bits indicate various types of data:

• 0–1: The

speed mode

–

00b: High.

–

01b: Standard.

–

10b: Economy.

–

11b: Turtle.

•  2: Lift lock status. 0b = inactive.
•  3: Parking status. 0b = inactive.
•  4: Seat status. 0b = inactive.
•  5: Pump status. 0b = off.
•  6–7:

Reserved

The BDI percentage.

2–5

The keyswitch hour meter data.

The 3301T hour meters provide a resolution of 0.1 hours.

For example, F423Fh indicates 99999.9 hours.

The vehicle unlock control status. 0b = lock, 1b = unlock.

Reserved

Byte(s)

Description

The following bits indicate the statuses of various display elements:

• 0: Whether the oil filter icon is displayed. 1b = displayed.
• 1–3: The

direction icons

–

001b = Neutral.

–

010b = Forward.

–

011b = Backward.

–

100b = Left turn.

–

101b = Right turn.

–

Other values: A direction icon is not displayed.

• 4–7: The

forklift status icons

(reach trucks and order pickers screen):

–

0001b: Inactive lift.

–

0010b: Lift up.

–

0011b: Lift down.

–

0100b: Lift left.

–

0101b: Lift right.

–

0110b: Lift up and left.

–

0111b: Lift up and right.

–

1000b: Lift down and left.

–

1001b: Lift down and right.

–

1010b: Rotate clockwise.

–

1011b: Rotate counterclockwise.

–

1100b: Shift left.

–

1101b: Shift right.

–

Other values: A forklift status icon is not displayed.

Содержание 3301T
































































Результаты поиска

Содержание 3301T

Отзывы:

Бренды по названию

Популярные бренды

Curtis 3301T, Руководство пользователя

Результаты поиска

Содержание 3301T

Отзывы:

Бренды по названию

Популярные бренды