Curtis 3301T Скачать руководство пользователя страница 48

Страница: 48 / 63

4 — PROGRAMMABLE PARAMETERS

Curtis Model 3301T Digital Instrumentation – September 2021

Return to TOC

pg. 42

PI Menu

The 3301T has a proportional/integral current controller, which is configured by the parameters on

the PI menu.

PI MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

0x66B0:00

1–100%

20–2048

16-bit

OEM Dealer

Specifies the proportional gain factor of the current

PI controller.

0x66C0:00

1–100%

20–2048

16-bit

OEM Dealer

20%

Specifies the integral gain factor of the current

PI controller.

MISC MENU

The following table describes the parameters on the Misc menu.

MISC MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Mode Saving

0x4800:00

Off/On

0–1

32-bit

Field Intermediate

Specifies whether the speed mode is saved when

the 3301T is powered down. On indicates that the

speed mode is saved.

PIN Code Source

0x3102:00

Enumerated

0–2

32-bit

Field Intermediate

None

Specifies whether a password is required when the

3301T is powered up and whether the 3301T or the

ECS is used to enter the password:

0 = None. A password is not required.
1 = Internal. The 3301T is used.
2 = External. The ECS is used.

HYD Controller Enable

0x6900:00

Off/On

0–1

32-bit

Field Intermediate

Specifies whether fault codes for the hydraulic

controller are displayed. On indicates the fault codes

are displayed.

Buzzer Alarm

0x6901:00

Off/On

0–1

32-bit

Field Intermediate

Enables or disables the buzzer. On enables

the buzzer.

Programmer Protocol

0x6902:00

Enumerated

0–1

32-bit

Field Immediate

ESP/SP

Specifies the protocol used for a Curtis

programming device:

0 = ESP/SP. For the serial version of the 1313

Handheld Programmer.

1 = CIT. For the Curtis Integrated Toolkit

(CIT)

and the CANbus version of the 1313

Handheld Programmer.

Vehicle Config

0x6909:00

1–65535

32-bit RW

OEM Dealer

Specifies the type of vehicle that is being used with

the 3301T. The correct value must be entered in

order to

view fault names

If you are not sure of the correct value, contact your

Curtis distributor or the Curtis sales and support

office in your region.

Startup Logo Select

0x3108:00

Enumerated

0–1

32-bit

Field Intermediate

None

Specifies whether the Curtis logo is displayed when

the 3301T is powered up:

0 = None
1 = Curtis

Содержание 3301T
































































Результаты поиска

Содержание 3301T

Отзывы:

Бренды по названию

Популярные бренды

Curtis 3301T, Руководство пользователя

Результаты поиска

Содержание 3301T

Отзывы:

Бренды по названию

Популярные бренды