Curtis 1356 Скачать руководство пользователя страница 17

Страница: 17 / 58

Curtis 1356/1356P CAN Expansion Module Manual,

Rev. A

2 — INSTALLATION & WIRING:

I/O Signal Specifications

Analog Inputs

The 1356 /1356P has five 0 – 15 V analog inputs. These inputs are scaled down

by 5.76, clamped to 3.3 V, and read by a 12-bit ADC internal to the MCU.

ANALOG INPUT SPECIFICATIONS

protected

voltage

signal

name

voltage

input

impedance

range

Analog Input 1 J1-20

Nominal input voltage:

Voltage Input Type:

Analog Input 2 J1-9

0 – 15 V

about 21 kΩ

Analog Input 3 J1-21

Input maximum

Resistance Input Type

: -1 V to B+

Analog Input 4 J1-10

reverse voltage:

-1.7 V about 1 kΩ

Analog Input 5 J1-22

The maximum resistive input on each analog input is 7.5 kΩ. The resistive or

voltage type of analog input can be selected by a Curtis programmer (1313/1314)

or CAN SDO message.

These five analog inputs can also be used as digital inputs. A unique fea-

ture of these digital inputs is that the active high/low thresholds are completely

programmable. Thus, these inputs can be used with analog sensors to detect

conditions like over/under pressure, high/low level points, etc.

Encoder Inputs

Analog Inputs 4 and 5 can be configured as a quadrature encoder input (En-

coder A and B). This standard quadrature encoder input accepts open collector

encoders with pull-up resistors in the 1356 /1356P module. The encoder can be

powered from the +5V supply (J1-12) or the +12V supply (J2-4) while using

the I/O GND (J1-24) as a common.

ENCODER INPUT SPECIFICATIONS

protected

encoder

frequency

input

voltage

phase

max

iimpedance

range

A J1-10

1 k

B J1-22

1.0 V

2.2 V

15 kHz

(internal pull-up

-1 V to B+

to +4.4 V)

Содержание 1356



























































Результаты поиска

Содержание 1356

Отзывы:

Curtis 1356, Руководство пользователя, Страница: 17 / 58

Результаты поиска

Содержание 1356

Отзывы: