Curtis Dyna-Fog BLACKHAWK 2620 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 55

background image

6. The Inlet Needle Valve may be stuck in its seat. This frequently occurs when stale

gasoline is used, or when the machine is left setting for long periods of time. To solve this

problem the Metering Diaphragm Cover and Metering Diaphragm may have to be removed

and the Inlet Needle Valve manually broken loose. See the section on the CARBURETOR.

Use Dyna-Fog

®

Fuel Stabilizer to reduce these types of problems.

TROUBLE SHOOTING

Symptom:

Machine floods easily.

Check:

1. Is the Fuel Needle properly set?

2. The spark plug gap must be properly set. If gap is too close, the gasoline will fill the gap and

prevent spark from occurring.

3. Primer pump being depressed excessively.

4. Batteries may be weak.

Symptom:

The engine runs weak.

Check:

1. Make sure the On-Off Control linkage is properly set. Linkage wheel should rotate fully

counterclockwise to STOP. If not, adjust linkage. See page 22.

2. Is there a carbon build-up? Check by looking with a flashlight. Refer to the MAINTENANCE

section.

3. Is there an air leak at the bottom of the Carburetion Assembly?

4. Is the Fuel Needle out of adjustment causing the machine to run weak? See the CARBURETOR

section.

5. Is the gasoline bad or dirty?

6. Are there large amounts of air in the gasoline line? Air bubbles make the machine run weak.

Check the fuel line connections, including the two lines from the primer bulb to the Carburetor.

Symptom:

The machine will not fog.

Check:

1. Is the Formulation Tank pressurized when the machine is running? If not, the pressurizing valve

is bad or installed backwards.

2. Check the formulation delivery lines from the tank to the injection point on the engine to see if

they are clogged.

3. Is the pressurizing valve in backwards? See the section on WORKING PRINCIPLES.

4. Check for carbon at the injection point. See MAINTENANCE section.

5. Does the Formulation Tank Cap leak?

33

«
...
31
32
33
34
35
...
»

Содержание BLACKHAWK 2620
























































Отзывы:

Нет отзывов

Похожие инструкции для BLACKHAWK 2620

Бренд: Janome Страницы: 80

Бренд: Necchi Страницы: 40

Бренд: JUKI Страницы: 2

Wertarbeit EU-7

Бренд: W6 Страницы: 83

Бренд: Windsor Страницы: 22

Бренд: Dixie Narco Страницы: 14

ReadySpace 1610

Бренд: Tennant Страницы: 2

FLEX-A-LITE 2600

Бренд: B&G Страницы: 4

TRIDENT T26 SC PLUS

Бренд: Hillyard Страницы: 28

Бренд: National Страницы: 27

Бренд: Nobles Страницы: 3

Бренд: Olivetti Страницы: 269

Бренд: Pfaff Страницы: 50

Бренд: Singer Страницы: 18

Бренд: JUKI Страницы: 42

505 PANTHER PLUS

Бренд: National Страницы: 27

Бренд: Ricoh Страницы: 134

Бренд: Panasonic Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды