Curtis Dyna-Fog BLACKHAWK 2620 Скачать руководство пользователя страница 8

Страница: 8 / 55

OPERATION

CAUTION

Read this compete OPERATION Section and the Section on SAFETY PRECAUTIONS before

starting the machine for the first time.

PREPARING THE ENGINE FOR OPERATION

1. When operating this machine for the first time, move to an un-congested and well-ventilated work

area in an open area away from flammable materials. Place the machine on a concrete pad or a

stable workbench.

2. Remove Fuel Tank Cap and fill the fuel Tank with either regular or unleaded gasoline.

CAUTION

Gasoline with a minimum of 87 Octane should be used. Use clean gasoline. Dirty gasoline

can promptly overload the fuel filter. Water in the gasoline can cause unexplained stops.

Very old or stale gasoline has a detrimental effect on the rubber seals in the fuel system and

causes hard starting because it vaporizes poorly.

3. Place the Fuel Tank Cap on the fuel Tank and turn the cap firmly in the clockwise (CW) direction

until the stop is reached.

4. Wipe any spilled gasoline from the machine and allow time for any unseen spills to evaporate.

CAUTION

Do not put any formulation in the machine until you have become familiar with starting and

stopping the pulse jet engine.

ENGINE OPERATION

CAUTION

Read the complete OPERATION section and the section on SAFETY PRECAUTIONS before

operating the engine.

NOTE

Abbreviated starting and clearing procedures are shown on the instruction label attached to the

machine; however, these should be used as reference only after you are thoroughly familiar with the

procedures.

CAUTIONS

and

WARNINGS

contained in this manual.

These instructions are intended to be used only as an approximate guide for starting the pulse jet

engine. Your starting procedure may vary slightly, depending on the density of the air where you are

starting your engine. Altitude, atmospheric pressure, and temperature all interact to affect air

density.

Содержание BLACKHAWK 2620
























































Результаты поиска

Содержание BLACKHAWK 2620

Отзывы:

Похожие инструкции для BLACKHAWK 2620

Бренды по названию

Популярные бренды

Curtis Dyna-Fog BLACKHAWK 2620, Инструкция по эксплуатации

Результаты поиска

Содержание BLACKHAWK 2620

Отзывы:

Похожие инструкции для BLACKHAWK 2620

Бренды по названию

Популярные бренды