Cub Cadet 3X 24 Скачать руководство пользователя страница 25

Страница: 25 / 28

Troubleshooting

Problem

Cause

Remedy

Engine fails to start

Choke not in CHOKE position.

2. Spark plug wire disconnected.

Fuel tank empty or stale fuel.

4. Engine not primed.

5. Faulty spark plug.

6. Key not in ignition on engine.

7. Extension cord not connected.

Move choke to CHOKE position.

2. Connect wire to spark plug.

Fill tank with clean, fresh gasoline.

4. Prime engine as instructed in the Engine

Operator’s Manual.

5. Clean, adjust gap, or replace.

6. Insert key fully into the switch.

7. Connect one end of the extension cord to the

electric starter outlet and the other end to a

three-prong 120-volt, grounded, AC outlet.

Engine running erratically/

inconsistent RPM (hunting

or surging)

Engine running on CHOKE.

2. Stale fuel.

Water or dirt in fuel system.

4. Carburetor out of adjustment.

5. Engine over-governed

Move choke lever to RUN position.

2. Fill tank with clean, fresh gasoline.

Drain fuel tank. Refill with fresh fuel.

4. Contact an authorized Service Center.

5. Contact an authorized Service Center.

Engine overheats

Carburetor not adjusted properly.

Contact an authorized Service Center.

Excessive vibration

Loose parts or damaged auger.

Stop engine immediately and disconnect spark

plug wire. Tighten all bolts and nuts. If vibration

continues, have unit serviced by an authorized

Service Center.

Loss of power

Spark plug wire loose.

2. Gas cap vent hole plugged.

Connect and tighten spark plug wire.

2. Remove ice and snow from gas cap. Be certain

vent hole is clear.

Unit fails to propel itself

Drive control cable in need of adjustment.

2. Drive belt loose or damaged.

Friction wheel worn.

Adjust drive control cable. Refer to Maintenance

& Adjustments section.

2. Replace drive belt. See authorized service dealer.

Replace friction wheel. Refer to Service section.

Unit fails to discharge snow

Chute assembly clogged.

2. Foreign object lodged in auger.

Auger control cable in need of

adjustment.

4. Auger belt loose or damaged.

5. Shear pin(s) sheared.

Stop engine immediately and disconnect spark

plug wire. Clean chute assembly and inside of

auger housing with clean-out tool or a stick.

2. Stop engine immediately and disconnect spark

plug wire. Remove object from auger with clean-

out tool or a stick.

Refer to Auger Control Test.

4. Refer to Maintenance & Adjustments section.

5. Replace with new shear pin(s).

Chute fails to easily rotate

180 degrees

Chute assembled incorrectly.

Unassemble chute control and reassemble as

directed in the Assembly section.

Содержание 3X 24





























Результаты поиска

Содержание 3X 24

Отзывы:

Похожие инструкции для 3X 24

Бренды по названию

Популярные бренды

Cub Cadet 3X 24, Руководство оператора

Результаты поиска

Содержание 3X 24

Отзывы:

Похожие инструкции для 3X 24

Бренды по названию

Популярные бренды