background image

Controls and Features

4

15

Snow thrower controls and features are described below and 

illustrated in Figure 4-1. 

Shift Lever

The shift lever is located in the right side of the 

handle panel and is used to determine ground 

speed and direction of travel.

Forward

There are six forward (F) speeds. Position one (1) is 

the slowest and position six (6) is the fastest. 

Reverse

There are two reverse (R) speeds. One (1) is the 

slower and two (2) is the faster.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust 

upward for hard-packed snow. Adjust downward when 

operating on gravel or crushed rock surfaces. See Set-Up & 

Assembly section.

Augers

When engaged, the augers rotate and draw snow into the auger 

housing.

Chute Assembly

Snow drawn into the auger housing is discharged out the chute 

assembly.

Headlight

The headlight is located on the handle panel and is automatically 

turned on when the engine is started.

† If Equipped

Drive Control

Headlight

Chute Assembly

Clean Out 

Tool

Drift Cutter †

Augers

Skid Shoe

Shift Lever 4-Way Chute Directional Control/ 

Two-Way Chute-Pitch Control †

Auger Control

Steering Trigger Control

Overhead Chute 

Directional Control †

Heated Grips †

Figure 4-1

Содержание 3X 24





























Отзывы: