background image

The limited warranty set forth below is given by Cub Cadet LLC with 
respect to new merchandise purchased and used in the United States, its 
possessions and territories, and by MTD Products Limited with respect to 
new merchandise purchased and used in Canada and/or its territories and 
possessions.
“Cub Cadet” warrants this product against defects in material and 
workmanship for a period of three (3) years commencing on the date of 
original purchase and will, at its option, repair or replace, free of charge, 
any part found to be defective in materials or workmanship.  This limited 
warranty shall only apply if this product has been operated and maintained 
in accordance with the Operator’s Manual furnished with the product, and 
has not been subject to misuse, abuse, commercial use, neglect, accident, 
improper maintenance, alteration, vandalism, theft, fire, water, or damage 
because of other peril or natural disaster.  Damage resulting from the 
installation or use of any part, accessory or attachment not approved by 
Cub Cadet  for use with the product(s) covered by this manual will void 
your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and 
workmanship for a period of thirty (30) days from the date of purchase. 
Normal wear parts include, but are not limited to items such as: batteries, 
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow 
thrower skid shoes, shave plates, auger spiral rubber and tires. 
HOW TO OBTAIN SERVICE:  Warranty service is available, WITH 
PROOF OF PURCHASE, through your local authorized service 
dealer. To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact 
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call 
1-877-282-8684,  or log on to our Web site at www.cubcadet.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 
1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following cases:
a. 

The engine or component parts thereof. These items may  
carry a separate manufacturer’s warranty. Refer to applicable 
manufacturer’s warranty for terms  and conditions.

b. 

Log splitter pumps, valves, and cylinders have a separate one 
year warranty.

c. 

Routine maintenance items such as lubricants, filters, blade 
sharpening, tune-ups, brake adjustments, clutch adjustments, 
deck adjustments, and normal deterioration of the exterior finish 
due to use or exposure.

d. 

Cub Cadet does not extend any warranty for products sold or  
exported outside of the United States and/or Canada, and 
their respective possessions and territories, except those sold 
through Cub Cadet’s authorized channels of export distribution.

e. 

Replacement parts that are not genuine Cub Cadet parts.

f. 

Service completed by someone other than an authorized service 
dealer.

g. 

Transportation charges and service calls.

No implied warranty, including any implied warranty of merchant-
ability of fitness for a particular purpose, applies after the applicable 
period of express written warranty above as to the parts as identi-
fied. No other express warranty, whether written or oral, except as 
mentioned above, given by any person or entity, including a dealer 
or retailer, with respect to any product, shall bind Cub Cadet.  During 
the period of the warranty, the exclusive remedy is repair or replace-
ment of the product as set forth above.
The provisions as set forth in this warranty provide the sole and 
exclusive remedy arising from the sale.  Cub Cadet shall not be liable 
for incidental or consequential loss or damage including, without 
limitation, expenses incurred for substitute or replacement lawn care 
services or for rental expenses to temporarily replace a warranted 
product.
Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied warranty 
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the 
purchase price of the product sold.  

Alteration of safety features of the 

product shall void this warranty.  You assume the risk and liability for 
loss, damage, or injury to you and your property and/or to others and their 
property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original 
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY:  This limited war-
ranty gives you specific legal rights, and you may also have other rights 
that vary in different jurisdictions.
IMPORTANT:  Owner must present Original Proof of Purchase to obtain 
warranty coverage.

MANUFACTURER’S LIMITED WARRANTY FOR

    Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-8-282-8684

          MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238

Содержание 26





























Отзывы: