1644526G (406807)
2020-SEP-21
16
1644526G (406807)
2020-SEP-21
17
INSTALL HOSES - DOUBLE-ACTING
Install 9/16 ORB x 3/4 JIC straight adapters in both work ports on the electric pump. If needed, for good
hose routing, install 3/4 JIC x 3/4 JIC 90° swivel adapters to both of these adapters.
For the B-5 (Bert), C-8 (Charlie) & D-9 (Daniel) models, install 9/16 ORB male x 3/4 JIC male straight
adapters in both ports on the cylinder. For the D-10 (David), E-15 (Ernie) & F-18 (Floyd) models, install
3/4 ORB male x 3/4 JIC male straight adapters in both ports on the cylinder.
Connect the shorter 3/8” ID hose with 3/4 JIC fittings from the `C1’ port on the pump to the base end port
on the cylinder. Connect the longer 3/8” ID hose with 3/4 JIC fittings from the `C2’ port to the rod end
port. (See Fig. 14.)
NOTE: The `C2’ port is the power down port and has only 1000 PSI maximum pressure.
INSTALL HOSES - SINGLE-ACTING
Install a 9/16 ORB x 3/4-16 JIC straight adapter in the power port on the electric power unit, install a 3/4
JIC x 3/4 JIC 90° swivel adapter to this adpater and install a 1/4 NPT x 3/4-16 JIC male elbow in the port
on the angled face of the reservoir.
For the B-5 (Bert), C-8 (Charlie) & D-9 (Daniel) models, install 9/16 ORB male x 3/4 JIC male adapters
in both ports on the cylinder. For the D-10 (David), E-15 (Ernie) & F-18 (Floyd) models, install 3/4 ORB
male x 3/4 JIC male adapters in both ports on the cylinder.
Connect the shorter 3/8” hose with 3/4 JIC fittings from the base end port of the cylinder to the power port
on the electric power unit. Connect the longer 3/8” hose with 3/4 JIC fittings from the rod end port of the
cylinder to the port on the reservoir. (See Fig. 13.)
3/4 JICF x 3/4 JICM 90° ADAPTER
ELECTRIC SINGLE-ACTING
9/16 ORB x 3/4 JIC 90
ADAPTER
1/4 NPT x 7/16 JIC 90
ADAPTER
9/16 ORBM
x 3/4 JICM
ADAPTER
ELECTRIC POWER UNIT
POWER
PORT
Fig. 14
ELECTRIC DOUBLE-ACTING
CYLINDER
ELECTRIC POWER UNIT
9/16 ORB X 3/4 JIC
ADAPTER
9/16 ORB X 3/4 JIC
ADAPTER
9/16 ORB X 3/4 JIC ADAPTER
C2 PORT (LOWER)
9/16 ORB X 3/4 JIC
ADAPTER
C1 PORT (UPPER)
Fig. 15
Fig. 12
Connect Ground Cable
Connect Ground Cable
Connect Power Cable
Connect Power Cable
Double-Acting
Power Unit
Single-Acting
Power Unit
Locate the control in the cab and route the cable out of
the cab through a hole in the back of the cab. Connect
the control to the electric power unit using the 3- or
4-pin connector set.
After completing the wiring, install the motor start
switch cover over the start switch and secure with a
tie strap.
Start Switch
Cover
Fig. 13
