CROWN VERITY PS-001 Скачать руководство пользователя страница 12

10

LEAK TESTING 

• Never check for leaks with a match or open flame.

Leak testing must be performed: 

• Before lighting your Pro Steamer for the first time.

• Every time the propane cylinder is refilled, replaced, or any gas component is replaced.

(or)

• At least once per year. 

Perform the leak test outdoors in a well-ventilated area, away from any open flame, heat
or ignition sources. DO NOT SMOKE! Use only a 50/50 mixture of liquid soap and water
for leak testing. Do not use a match or open flame. 

THE FOLLOWING MUST BE CHECKED: 

• Cylinder valve including threads into tank.

• All cylinder welds.

• Control Regulator fitting(s) and cylinder connection.

• All hose and manifold connections.

1) Open LP cylinder valve to the Pro Steamer

2) Brush soap solution on all connections and components listed above.

3) Observe each place for growing bubbles, which indicate a leak, is present.

4) Tighten any leaking connection until a repeat test shows no evidence of leakage

(shut off gas supply while correcting any leaks). 

DO NOT USE THE Pro Steamer IF ANY LEAKS CANNOT BE STOPPED. TURN 
OFF THE GAS SUPPLY VALVE, REMOVE THE GAS CYLINDER, AND CALL A 
QUALIFIED GAS APPLIANCE SERVICE PERSON FOR REPAIRS.

WARNING! - NATURAL HAZARD - Spiders and other insects are attracted by the smell of
gas and could make webs or nests in the burner. This could partially or completely block
the flow of gas through the burner and is indicated by a sooty, yellow flame, and/or a
burner that is difficult or impossible to light. Ultimately, it may cause the gas to burn
inside the burner or at the air inlet, which can seriously damage your Pro Steamer. If this
happens: immediately shut off the propane at the cylinder, valve

To prevent and/or correct this occurrence, periodically check the burner for

obstructions by inserting a pipe cleaner or flexible wire through the air inlet of the burner,
and twisting it. 

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: (519) 751-1800

FAX: (519) 751-1802

www.crownverity.com

Email: [email protected]

Содержание PS-001
















Отзывы: