background image

INSTRUCTION MANUAL

MODEL 2016-05A Downconverter 

TABLE OF CONTENTS

      PAGE

Warranty

 2

1.0  General

 3

1.1  Equipment Description

 3

1.2  Technical Characteristics

 4

1.3  Monitor & Control Interface

 5

2.0  Installation

 7

2.1  Mechanical

 7

2.2  Rear Panel Inputs & Outputs

 8 

2.3  Front Panel Controls & Indicators

 9

2.4  Operation

10

2.5  Menu Settings

11

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and 
workmanship for a period of one year after shipment to customer.  Cross Technologies, 
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s 
option, replacing parts, subassemblies, or entire assemblies.  Cross Technologies, Inc. shall 
not be liable for any special, indirect, or consequential damages.  This warranty does not 
cover parts or equipment which have been subject to misuse, negligence, or accident by the 
customer during use.  All shipping costs for warranty repairs will be prepaid by the 
customer.  There are not other warranties, express or implied, except as stated herein.

C

ROSS 

T

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com 

E-MAIL [email protected]

2016-05A Manual, Rev A 

 

   Page 2

    

                  04/17/17

Содержание 2016-05A

















Отзывы: