CRL VE-1P Скачать руководство пользователя страница 36

Страница: 36 / 36

CRL EDGER ACCESSORIES AND PARTS

Board Dressing Plates and Sticks

8" x 6" (203 mm x 152 mm) Board Dressing Plates
are used on the Polishing Wheel by
running them through the machine like a piece
of glass.
6" x 2" (152 mm x 51 mm) Dressing Sticks are
used to dress the Diamond Wheels by hand from
the front of the machine.

46205880

1/4" (6 mm) Thick Board Dressing Plate

46205881

3/8" (10 mm) Thick Board Dressing Plate

46205882

1/2" (12 mm) (Thick Board Dressing Plate

46205871

1/4" (6 mm) Thick Dressing Stick

Minimum order is one each.

Synthetic Blue Powder Coolant

Biodegradable, anti-foaming Coolant Powder
mixes with water for high lubricity. Inhibits rust and
dissipates heat. Mix ratio is 100:1.

2651005

1 lb. (.453 kg.) Bag of Coolant

Minimum order is one each.

CRL EDGER WHEELS

Diamond Pencil Edge Wheels

7" (178 mm) diameter Diamond Wheel for pencil
edge profiling. 140-170 grit.

36443213

For 1/8" to 1/4" (3 to 6 mm) glass

36881012

For 3/16" to 3/8" (5 to 10 mm) glass

38404909

For 1/4" to 1/2" (6 to 12 mm) glass

Minimum order is one each.

Diamond Flat and Seam Wheels

7" (178 mm) diameter Diamond Wheel for Flat and
Seam profiling. 140-170 grit.

38533510

For 1/8" to 1/4" (3 to 6 mm) glass

38386909

For 3/16" to 3/8" (5 to 10 mm) glass

38517503

For 1/4" to 1/2" (6 to 12 mm) glass

Minimum order is one each.

Diamond 30 Degree Miter Wheel

7" (178 mm) diameter Diamond Wheel for
30 degree miter profiling. 140 grit.

38677802

For 1/8" to 1/2" (3 to 12 mm) glass

Minimum order is one each.

Grind Wheel Hub

Holds 2 wheels and fits the spindle motor on the
VE1P/AU11. Use to mount extra set-ups.

38430304

Grind Wheel Hub

Minimum order is one each.

Orange Polish Wheel

For 1/8" to 1/2" (3 to 12 mm) glass. 7-1/4"
diameter x 3/4" (184 mm x 19 mm) thick. Always
use the original Orange Wheel for best results.

39666000

For 1/8" to 1/2" (3mm to 12mm) glass

Minimum order is one each.

CAT. NO. APPLICATION

CAT. NO. DESCRIPTION

CAT. NO. APPLICATION

Pencil

Miter

Flat & Seam

Owner’s Manual

VE-1P Vertical Edger

Factory Replacement Parts and Accessories for the VE-1P/AU11 Edger

Glass Rail Rack Parts
for VE1P/AU11 Edgers
built in June 2013
and after

Each 39982900 Support
Bracket requires a
39501206 Spacer Tube.

Glass Rail Support Bracket

The one-piece bracket slides onto the new
Glass Rail Rack sections.

39982900

Rail Support Bracket

Minimum order is one each.

Spacer Tube, Plastic

Use these spacers over the above Rail
Brackets.

39501206

Bracket Spacer Tube

Minimum order is one each.

CAT. NO. DESCRIPTION

Parts Page 35

Содержание VE-1P





































Результаты поиска

Содержание VE-1P

Отзывы:

Похожие инструкции для VE-1P

Бренды по названию

Популярные бренды

CRL VE-1P, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VE-1P

Отзывы:

Похожие инструкции для VE-1P

Бренды по названию

Популярные бренды